background image

Page 12                                                                                   XBase 09 Operating Manual

Now  hold  down  the  Closed  Hi  Hat  pad  and  -while  holding  it  down-  hit  Note  buttons  9  and  10
twice...  both  Note  Buttons  9  and  10  should  be  blinking.  Now  turn  the  Hi  Hat  Tune  knob  and
select a pitch for the Rim. Once you've got a good pitch, hit buttons 9 and 10 twice each again to
take them out of record. If you'd like either of those, hit louder, hit the Accent pad and select 9
and/or 19. Hit the Accent button again to come out of Accent mode.

Now, push the Open Hi Hat pad. Select Note buttons 1 and 13. Press Shift, and while holding it
down, hit Button 13 again. Use Up/Down to scroll to „CLP". Hit Button 13 to light it, then hit the
Enter Button. Note 13 becomes a Clap. By hitting the Accent mode, you can choose Button 13 to
make the claps louder. (Remember to hit the Accent pad again to come out of Accent). Now hold
down the Open Hi Hat pad and hit button 13 twice. Use the Hi Hat Tune knob and the OH Decay
knob to find a clap sound you like. Once you've found it, hit button 13 twice to deselect it from
recording.

Now push the Shift button, hold it down and hit Note button 13 again. Use the Up/Down keys to
scroll  until  the  display  reads  „CrH",  then  hit  Note  button  1  and  „Enter".  There  is  now  a  crash
cymbal on Note 1.

... Turn up the Bass and Snare Drum volumes,

sit back and listen to what you've created so far!

... On to new frontiers!

Hit  the  „Shift"  button,  hold  it  down  and  hit  Note  button  #6  (Shuffle).  Use  the  Down  button  to
make the display read „2", which will swing the notes we choose to be a little late to the beat. Hit
the Note buttons 2,  4,  6,  8,  10,  12,  14,  16.  Hit  the  „Enter"  button.  Notice  that  the  „feel"  of  the
track  has  changed.  If  you  like  that  sound,  move  to  the  next  paragraph,  or  to  change  it  back  to
„straight  time",  hit  the  „Shift"  button,  hold  it  down  and  hit  Note  button  6  (shuffle).  Use  the
Up/Down  buttons  to  make  the  display  read  „0",  then  light  all  of  the  unlit  note  buttons  and  hit
„Enter".

Hit the „Write" button twice so that it is lit.
Solo the HiHat by turning down the Bass Drum and Snare drum volumes.
Hit the Shift button, hold it down and select Note button 15 (LFO Page).
Turn the Bass Drum Decay (LFO Intensity) control so the display reads „000 or 001".
Turn the Bass Drum Tune (LFO Waveform) control so the display reads „tri".
Turn the Bass Drum Pitch (LFO Destination) control so the display reads „Htu".
Turn the Bass Drum Harmonics (LFO Speed) control so the display reads „004".
Turn the Bass Drum Pulse (LFO Sync) control so the display reads „SYn".

Now, turn the Bass Drum Decay (LFO Intensity) control so the display reads „010".

Hit the „Enter" button.

Hit the „Stop" button and then hit the „Write" button so that ist light goes out.
Turn up the Bass Drum and Snare Drum levels.

... Now, kick back, hit „START" and listen to your creation !

Содержание Xbase 09






































Отзывы: