manualshive.com logo in svg

Johnson Pump MCHC, Инструкция по эксплуатации

Поделиться
Скачать
Johnson Pump MCHC Скачать руководство пользователя страница 45

44

Disassembly and assembly

MCHZ/EN (0912) 4.2

7.8.4

Assembling the stuffing box packing MCHZ

1 Fit the 5 packing rings. Place the packing rings with the openings offset. The packing 

rings may only be bent open axially, see figure 15.

2 Fit the gland (0170). Tighten the nuts (0350) by hand.

3 Proceed with paragraph 7.8.6.

7.8.5

Assembling the mechanical seal MCHZS

 !

A mechanical seal is a vulnerable precision component. Leave the seal in the 
original packaging until you start with the actual assembly. Ensure that the 
working environment is dust free and that the parts and tools are clean. 
Remove any paint from the components. Never place the slide rings on the 
slide surfaces and never touch the slide surfaces with ones fingers!

1 Fit the set ring (0120) and lock it with the adjustment screw (0400). The distance 

between the set ring and the nearest external circlip groove must be 

64,5 mm

.

2 Before fitting check whether the grooves for the external circlips (0290) have any 

sharp edges.

3 Wet the clean shaft with some low-surface-tension water (add detergent) and feed 

the bellows part of the seal (0230) with a slight twist in clockwise direction onto the 
shaft. 

Apply pressure or tension during assembly via the rear end of the 

spring only.

 The sliding surface must face towards the shaft end, drive side. 

4 Wet the seal chamber with some low-surface-tension water (add detergent) and fit 

the static ring of the mechanical seal (0230) into the seal cover (0040), with the 
sliding surface pointing out.

5 Fit the gasket (0200) and fit the cover (0040) into the pressure bracket.

6 Proceed with paragraph 7.8.6.

Figure 15:

Bending open of gland packing rings.

Содержание MCHC























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды