manualshive.com logo in svg

Johnson Pump MCHC, Инструкция по эксплуатации

Поделиться
Скачать
Johnson Pump MCHC Скачать руководство пользователя страница 20

MCHZ/EN (0912) 4.2

Installation

19

MCHZ

3.6

Installation

3.6.1

Piping

Fit the gaskets between the flanges and connect the pressure and the suction pipes to 
the pump.

3.6.2

Installation of a pump unit

Pump and motor shafts of complete pump units are adjusted perfectly in line in the 
works.

1 In case of permanent arrangement place the base plate level on the foundation with 

the aid of shims.

2 Carefully tighten the nuts on the foundation bolts.

3 Check the alignment of pump and motor shafts and if necessary realign, see 

paragraph 3.6.4 "Alignment of the coupling".

3.6.3

Assembling a pump unit

If the pump and the electric motor still have to be assembled, do the following:

1 Fit both halves of the coupling to the pump shaft and the motor shaft respectively.

2 If the shaft height of the pump is not equal to the IEC size of the motor, level up the 

difference by placing properly sized spacers under the pump or under the motor feet.

3 Place the pump on the base plate. Fix the pump to the base plate.

4 Place the electric motor on the base plate. Move the motor to obtain a gap of 3 mm 

between both coupling halves. 

5 Place copper shims under the feet of the electric motor. Fix the electric motor to the 

base plate. 

6 Align the coupling in accordance with the following instructions.

3.6.4

Alignment of the coupling

1 Place a ruler (A) on the coupling. Place or remove as many copper shims as is 

necessary to bring the electric motor to the correct height so that the straight edge 
touches both coupling halves over the entire length, see figure 4.

2 Repeat the same check on both sides of the coupling at the height of the shaft. Move 

the electric motor so that the straight edge touches both coupling halves over the 
entire length.

3 Check the alignment once again using a pair of external callipers (B) at 2 diametrical 

opposite points on the sides of the coupling halves, see figure 4.

4 Fit the guard.

Figure 4:

Aligning the coupling by means of a ruler and a pair of outside callipers.

B

A

Содержание MCHC























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды