manualshive.com logo in svg

Johnson Pump MCHC, Инструкция по эксплуатации

Поделиться
Скачать
Johnson Pump MCHC Скачать руководство пользователя страница 11

10

Introduction

MCHZ/EN (0912) 4.2

1.3

Guarantee

Johnson Pump shall not be bound to any guarantee other than the guarantee accepted 
by Johnson Pump. In particular, Johnson Pump will not assume any liability for explicit 
and/or implicit guarantees such as but not limited to the marketability and/or suitability of 
the products supplied.

The guarantee will be cancelled immediately and legally if:

• Service and/or maintenance is not undertaken in strict accordance with the 

instructions.

• The pump is not installed and operated in accordance with the instructions.

• Necessary repairs are not undertaken by our personnel or are undertaken without our 

prior written permission.

• Modifications are made to the products supplied without our prior written permission.

• The spare parts used are not original Johnson Pump parts.

• Additives or lubricants used are other than those prescribed.

• The products supplied are not used in accordance with their nature and/or purpose.

• The products supplied have been used amateurishly, carelessly, improperly and/or 

negligently.

• The products supplied become defective due to external circumstances beyond our 

control.

All parts which are liable to wear are excluded from guarantee.

 Furthermore, all 

deliveries are subject to our “General conditions of delivery and payment”, which will be 
forwarded to you free of charge on request. 

1.4

Inspection of delivered items

Check the consignment immediately on arrival for damage and conformity with the advice 
note. In case of damage and/or missing parts, have a report drawn up by the carrier at 
once.

1.5

Instructions for transport and storage

1.5.1

Dimensions and weight

A pump or a pump unit is generally too heavy to be moved by hand. Therefore, use the 
correct transport and lifting equipment. Dimensions and weight of the pump or pump unit 
are shown on the label on the cover of this manual.

1.5.2

Use of pallets

Usually a pump or pump unit is shipped on a pallet. Leave it on the pallet as long as 
possible to avoid damages and to facilitate possible internal transport.

 !

When using a forklift always set the forks as far apart as possible and lift the 
package with both forks to prevent it from toppling over! Avoid jolting the 
pump when moving it!

Содержание MCHC























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды