manualshive.com logo in svg

Johnson Pump MCHC, Инструкция по эксплуатации

Поделиться
Скачать
Johnson Pump MCHC Скачать руководство пользователя страница 19

18

Installation

MCHZ/EN (0912) 4.2

3.4

Piping

• The piping to the suction and delivery connections must fit exactly and must not be 

subject to stress during operation.

• The passage of the suction pipe must be amply dimensioned. This pipe should be as 

short as possible and run towards the pump in such a way that no air pockets can 
arise. If this is not possible, a venting facility should be provided at the highest point of 
the pipe. If the inside diameter of the suction pipe is larger than the suction connection 
of the pump, an eccentric reducer should be applied to prevent air pockets and whirls 
See figure 3.

• The maximum allowable system pressure is stated in paragraph 10.2 "Permissible 

pressure and temperature". If there is a risk that this pressure might be exceeded, for 
instance because of an excessive inlet pressure, appropriate measures should be 
taken by mounting a safety valve in the piping.

• Sudden changes in the rate of flow can lead to high pressure impulses in the pump 

and the piping (water shock). Therefore, do not use quick-acting closing devices, 
valves etc.

3.5

Accessories

• Fit any parts that may have been supplied separately. 

• If the liquid does not flow towards the pump, fit a foot valve at the bottom of the 

suction pipe. If necessary, combine this foot valve with a suction strainer to prevent 
impurities from being drawn in.

• When mounting, place temporarily (for the first 24 operating hours) a fine gauze 

between suction flange and suction pipe to prevent internal pump parts from being 
damaged by foreign matter. If the risk of damage continues to exist, fit a permanent 
filter.

Figure 3:

Eccentric reducer to suction flange.

Содержание MCHC























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды