Johnson Pump MCHC Скачать руководство пользователя страница 37

Страница: 37 / 86

Disassembly and assembly

MCHZ/EN (0912) 4.2

7.5.5

Disassembling the ball bearings

1 Remove both internal circlips (0240) from the bearing bracket.

2 Using a suitable bush, resting on the outer ring of the bearing, press the bearings out

of the bearing bracket.

7.5.6

Disassembling the mechanical seal MCHZS

1 Remove the seal cover (0090) from the pump shaft and remove the static ring from

the mechanical seal.

2 Slide the rotating ring for the mechanical seal (0160) off the pump shaft.

If the reason for disassembly was to replace the mechanical seal, the new mechanical
seal can now be fitted. See from paragraph 7.6.5 for this.

7.5.7

Disassembling the set of stage casings

1 Uncouple the balance pipe (0670) if fitted.

2 Only for MCHZS: Slacken the adjustment screw (0330) and remove the set ring

(0190).

3 Unscrew the nuts (0750) from the tie rods (0740).

4 Remove the pump casing (0030) from the stage set. Using a suitable bush, press or

tap the throttling bush (0060) out of the inlet casing.

5 Remove the external circlip (0100) and any throttling sleeve (0600) from the pump

shaft.

6 Remove the end cover (0040) and the air wheel (0050). Remove the key (0730) from

the shaft and remove the gasket (0180).

7 Remove the pump cover (0530) and remove the external circlip (0090).

8 Remove all impellers (0520), stage casings (0510) and keys (0730).

9 Remove the suction cover (0500) from the pump casing (0030).

7.5.8

Disassembling the bearing housing on the suction side

1 Position the pump casing with the shaft horizontally.

2 Remove the rear bearing cover (0130).

3 Continue from step 5 of paragraph 7.5.4.

7.5.9

Disassembling the ball bearing on the suction side

See paragraph 7.5.5, with the exception of step 1.

7.5.10

Disassembling the mechanical seal on the MCHZS suction side

See paragraph 7.5.6, for which item no. (0160) now becomes: item no. (0150).

Содержание MCHC























































































Результаты поиска

Содержание MCHC

Отзывы:

Бренды по названию

Популярные бренды

Johnson Pump MCHC, Инструкция по эксплуатации

Результаты поиска

Содержание MCHC

Отзывы:

Бренды по названию

Популярные бренды