Johnson Pump MCHC Скачать руководство пользователя страница 46

Страница: 46 / 86

MCHZ/EN (0912) 4.2

Disassembly and assembly

MCHZ

7.8.6

Assembling the bearing construction

See figure 16.

1 Fit the bearing cover (0140) to the inside of the bearing housing for the drive side,

this is the part which has the arrow for the direction of rotation.

2 Fit an internal circlip (0300) into the inner groove in the bearing housing.

3 Fix this bearing housing (0010) to the pressure bracket with the bolts (0360).

4 Fit the rubber V-ring (0310) over the pump shaft, with the narrow opening pointing to

the inside of the pump.

5 Fit the external circlip (0290) into the inner of the 2 grooves on the pump shaft and fit

the filling ring (0160).

6 Fit the bearing (0280) over the pump shaft and into the seat of the bearing housing

using a suitable assembly bush which rests on both the inner and outer rings of the
bearing.

7 Fit the other filling ring (0160) and external circlip (0290) to the pump shaft.

8 Fit the internal circlip (0300) into the bearing housing.

9 Fit the outermost bearing cover (0140) and the rubber V-ring (0310), with the narrow

opening pointing to the outside of the pump.

Figure 16:

Assembly of the double row ball bearing.

Содержание MCHC























































































Результаты поиска

Содержание MCHC

Отзывы:

Бренды по названию

Популярные бренды

Johnson Pump MCHC, Инструкция по эксплуатации

Результаты поиска

Содержание MCHC

Отзывы:

Бренды по названию

Популярные бренды