background image

T600HCx-3 Single-Stage Thermostats Installation Instructions

15

Resume: 

This selection cancels the permanent 

hold and enables the regular program schedule.

To enable or cancel the permanent hold feature while in 
the Main User Menu:

1.

Press the 

NO

 key to all prompts until the schedule 

hold prompt appears on the display. Press the 

YES

 

key to set the schedule hold type.

2.

Press the 

UP/DOWN

 arrow keys to locate the 

desired permanent hold type (or 

resume

 schedule). 

Press the 

YES

 key to enter the selection.

3.

Press the 

YES

 key to return to the Status Display 

Menu or press the 

NO

 key to change the schedule 

hold selection again.

Accessories

All the accessories in Table 8 include mounting 
hardware; contact the nearest Johnson Controls® 
representative to order any of these parts.

Note:

Review the technical specifications of the 

accessories prior to their use in an application.

Repair Information

If the T600HCx-3 thermostat fails to operate within its 
specifications, replace the unit. For a replacement 
thermostat, contact the nearest Johnson Controls 
representative.

  

   

Table 8:  Accessories (Order Separately)

Code Number

Description

SEN-600-1

Remote Indoor Air Temperature Sensor

SEN-600-4

Remote Indoor Air Temperature Sensor with Occupancy Override and LED

TE-6361M-1

1

Duct Mount Air Temperature Sensor

TE-636S-1

1

Strap-on Temperature Sensor

1.

Additional TE-636xx-x Series 10k ohm Johnson Controls Type II Thermistor Sensors are available; refer to the 

TE-6300 

Series Temperature Sensors Product Bulletin (LIT-216320)

 for more details.

Table 9:  Display Messages

Display

Function

Service

Indicates that there is a service alarm in accordance with the programmable Digital Inputs (DI1 or DI2)

Filter

Indicates that the filter(s) is dirty in accordance with the programmable Digital Inputs (DI1 or DI2)

Frost ON

Indicates that the heating is energized by the low limit frost protection room temperature setpoint.

SetClock

Indicates that there has been a power failure greater than 6 hours and the clock needs to be reset. 
(T600xxP-3 only.)

Содержание T600HCN-3

















Отзывы: