background image

 

Technical Specifications 

Product 

T600HCN-1 Non-Programmable Thermostat 

Power Requirements 

20-30 VAC, 50/60 Hz, 24 VAC nominal, Class 2 

Relay Contact Rating 

Maximum Inductive 

1 ampere with in-rush surges up to 3 amperes, 30 VAC maximum 

Digital Inputs 

Relay dry contact only across the C terminal to DI1 or DI2 

Recommended Wire Size 

18 gauge maximum, 22 gauge recommended 

Thermostat Measurement 

Range 

-40 to 122

°

F (-40 to 50

°

C) 

Sensor Type: 

Resolution: 

Control Accuracy: 

Local 10 K ohm NTC thermistor 

±

0.2 F

°

 (

±

0.1 C

°

±

0.9 F

°

 (

±

0.5 C

°

) @ 70

°

F (21

°

C) typical calibrated 

Outdoor Air Temperature 

Indication Range 

-40 to 122

°

F (-40 to 50

°

C) 

Setpoint Control Range 

Cooling: 54 to 100

°

F (12 to 37.5

°

C) in 1/2 degree increments 

Heating: 40 to 90

°

F (4.5 to 32

°

C) in 1/2 degree increments

 

Minimum Deadband 

(Between heating and cooling) 2 F

°

 or 1 C

°

 

Ambient Operating 

Conditions 

32 to 122

°

F (0 to 50

°

C); 0 to 95% RH noncondensing 

Ambient Storage 

Conditions 

-22 to 122

°

F (-30 to 50

°

C); 0% to 95% RH noncondensing 

Dimensions (H x W x D) 

4.94 x 3.38 x 1.13 in. (125 x 86 x 29 mm) 

Shipping Weight 

0.75 lb (0.34 kg) 

UL and cUL Listing 

File E27734 with CCN’s XAPX (US, UL 873) and XAPX7 (Canada, CSA C22.2 No. 24) 

CE Compliance 

CE Directives EN50081-1: 1992 EMC Emission; EN50082-2 EMC Immunity (Pending) 

FCC Compliance 

This equipment has been tested and found to comply with the limits for a Class A digital 
device and verified to Class B pursuant to Part 15 of FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference when this equipment is 
operated in a commercial environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. 

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or 
misuse of its products. 

 

This device complies with Class A Part 15 of the FCC rules. It was also verified to Class B. Operation is subject to 
the following two conditions: 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that may cause undesired operation. 

This Class A digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment 
Regulations. Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le materiél 
brouilleur du Canada. 

 

Controls Group 

507 E. Michigan Street 
P.O. Box 423 

Printed in U.S.A.

Milwaukee, WI  53201 

www.johnsoncontrols.com

T600HCN-1 Non-Programmable Thermostat Installation Instructions    

13

 

Содержание T600HCN-1














Отзывы: