Johnson Controls PGP914 Скачать руководство пользователя страница 1

Страница: 1 / 18

D-308495 PGP914 Rev.0

PGP914 Wireless PIR Motion Detector

Installation Guide

Installation guidelines

The reference to PGP914 throughout this manual includes the model PG9914.

CAUTION:

Only qualified personnel may install this equipment. Place this device in non-

hazardous indoor locations only.

Important:

Check the device and the entire alarm system weekly to ensure optimal

performance.

Note:

To comply with FCC and ISED Canada RF exposure compliance requirements, locate

the device at a distance of at least 20 cm from all persons during normal operation. Do not
co-locate the antennas used for this product, or operate them in conjunction with any other
antenna or transmitter.

Figure 1: PGP914

Callout

Description

Lens

Battery pull-tab

Enroll button

Tamper switch

*D-308495*

D-308495

Содержание PGP914



















Результаты поиска

Содержание PGP914

Отзывы:

Похожие инструкции для PGP914

Бренды по названию

Популярные бренды

Johnson Controls PGP914, Руководство по установке

Результаты поиска

Содержание PGP914

Отзывы:

Похожие инструкции для PGP914

Бренды по названию

Популярные бренды