Johnson Controls FX-PCV1615 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 30

background image

CAUTION

Risk of Property Damage

Rotate the damper to the full-open position before starting the air handler. Failure to rotate the damper

to the full-open position may result in damage to the VAV box or ductwork when the air handler is

started.

CAUTION

Risque de dégâts matériels

Faire pivoter le registre pour le placer en position d'ouverture complète avant de démarrer l'unité de

traitement d'air. Le non-respect de cette directive risque d'endommager le caisson de l'unité à volume

d'air variable (VAV) ou le réseau de conduites au démarrage de l'unité de traitement d'air.

Wiring diagram

Figure 2: PCV1615/1626/1628/1630 Controller wiring terminations and physical features

5

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

«
...
3
4
5
6
7
...
»

Содержание FX-PCV1615































Отзывы:

Нет отзывов

Похожие инструкции для FX-PCV1615

ClubSport Wheel Base V2

Бренд: FANATEC Страницы: 39

Бренд: Ickle Bubba Страницы: 23

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: IBC Страницы: 8

Бренд: Full Gauge Controls Страницы: 3

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Бренд: ITALCOPPIE SENSORI Страницы: 2

Бренд: R for Rabbit Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды