manualshive.com logo in svg

Johnson Controls FX-PCV1615, Руководство по установке, Страница: 2 / 30

Поделиться
Скачать
Johnson Controls FX-PCV1615 Скачать руководство пользователя страница 2

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause harmful

interference, in which case the users will be required to correct the interference at their own

expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Installation

Observe these guidelines when installing an FX-PCV1615/1626/1628/1630 controller:
• Transport the FX-PCV controller in the original container to minimize vibration and shock damage

to the FX-PCV controller.

• Do not drop the FX-PCV controller or subject it to physical shock.

Parts included

• One FX-PCV1615/1626/1628/1630 controller with removable SA bus and power terminal blocks.
• One installation instructions sheet.
• One self-drilling No. 10 x 25 mm (1 in.) screw.
• The FX-PCV1628 model includes a 1.25 inch extended length screw.

Materials and special tools needed

• Several 6 mm (1/4 in.) female spade terminals for input and output wiring, and crimping tool for

spade mounted terminal blocks.

• Small, straight-blade screwdriver for securing wires in the terminal blocks.
• 8 mm (5/16 in.) wrench or 10 mm (3/8 in.) 12-point socket to tighten the square coupler bolt.
• Several shims or washers to mount the FX-PCV.
• Power screwdriver, 100 mm (4 in.) extension socket, punch, drill, and 3.5 mm (9/64 in.) drill bits to

mount the FX-PCV.

• Pliers to open and close the damper.
• Required length of 3.97 mm (5/32 in.) ID pneumatic tubing and barbed fittings.

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

2

Содержание FX-PCV1615































Отзывы:

Нет отзывов