Johnson Controls FX-PCV1615 Скачать руководство пользователя страница 28

Страница: 28 / 30

Table 10: FX-PCV1615/1626/1628/1630 Controllers

Communications Bus

RS-485: selectable between BACnet MSTP or N2

FC Bus: 0.6 mm (22 AWG) standard 3-wire, twisted, shielded

cable recommended between the supervisory controller and
10/100 Mbps; 8-pin RJ-45 connector

SA Bus

: 0.6 mm (22 AWG) stranded, 4-wire (2-twisted pairs)

shielded cable recommended from the FX-PCV controller for

network sensors and other sensor/actuator devices; includes a

terminal to source 15 VDC supply power from FX-PCV to SA Bus

devices

Note:

For more information, refer to the

FX-PC Series

Controllers MS/TP Communications Bus Technical Bulletin

(LIT-12011670).

Processor

RX63N 32-bit Renesas microcontroller

Memory

1 MB flash memory and 512 KB RAM

Universal Input Mode/

Configurable Output Mode

Accuracy

UI Analog Input Mode:

15-bit resolution on UIs

CO Analog Output Mode (FX-PCV1626/FX-PCV1628/FX-

PCV1630 only):

0–10 VDC ± 200 mV

Air Pressure Differential

Sensor

Range: -1.5 in. to 1.5 in. W.C.

Performance Characteristics:

Accuracy: ±1.3% Full Span Maximum (±0.039 in. W.C.)

Note:

Combined error due to offset, non-linearity, and

temperature variation.

Typical accuracy at zero (null) pressure is ±0.02 in. W.C.(if

provided)

Note:

Includes error due to non-linearity.

Actuator Rating

4 N·m (35 lb·in) minimum shaft length = 44 mm (1-3/4 in.) (if

provided)

Mounting

Mounts to damper shaft using single set screw and to duct with

single mounting screw

Dimensions

(Height x Width x Depth)

165 mm x 125 mm x 73 mm (6.5 in. x 4.92 in. x 2.9 in.)

Center of Output Hub to Center of Captive Spacer:

135 mm

(5-5/16 in.)

Weight

0.65 kg (1.45 lb)

Compliance

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment; Suitable for use in other environmental air space

(plenums) in accordance with Section 300.22(C) of the National

Electric Code.
FCC Compliant to CFR47, Part 15, Subpart B, Class A.

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

Содержание FX-PCV1615































Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды

Johnson Controls FX-PCV1615, Руководство по установке

Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды