Johnson Controls FX-PCV1615 Скачать руководство пользователя страница 23

Страница: 23 / 30

Commissioning

Use the following procedure to commission the FX-PCV 1615/1626/1628/1630 controller:

1. Download the control application to the controller using the CCT. Refer to the

Controller Tool

Help (LIT-12011147)

2. Commission the VAV Box. Refer to the

Controller Tool Help (LIT-12011147)

3. Perform airflow balancing on the VAV box. Refer to the

VAV Box Balancing Tool and Network

Sensors Technical Bulletin (LIT-12011659)

4. Perform commissioning checkout procedures. Refer to the

Controller Tool Help (LIT-12011147)

You commission controllers with the CCT software. The controller can be connected in one of

four ways; either NxE Passthru, Bluetooth (using BTCVT), through MAP 4.2+/BACnet Router

(Mobile Access Portal (MAP) Gateway at version 4.2 or above), or Direct Ethernet connection to the

controller. Refer to

Controller Tool Help (LIT-12011147)

for detailed information on commissioning

field controllers.

Note:

The Bluetooth connection can be used to Transfer to Computer (Upload) and

commission the controller, but cannot be used to Transfer to Device (Download).

The CCT connects to the FX-PCV through a laptop computer using different connection options: the

Bluetooth Commissioning Converter, or the wired BACnet Ethernet to MS/TP Router can be used

when using the BACnet MS/TP protocol. These connection options require additional hardware

listed in Table 9.

Repair information

If the FX-PCV controller fails to operate within its specifications, replace the unit. For a replacement

unit, contact the nearest Johnson Controls representative.

Troubleshooting

Table 8 provides LED status indicator information for troubleshooting the FX-

PCV1615/1626/1628/1630 controllers. The table below provides some additional troubleshooting

information for possible problems.

Note:

If you experience short circuits in the 24 VAC power supply causing protective devices

such as breakers or fuses to trip, make sure that the power connections on the FX-PCV are not

reversed. The most common cause of this problem is when the 24 VAC power supply on the

FX-PCV is reversed but not reversed on a connected secondary device. Improper wiring of this

power terminal may cause a short circuit across the 24 VAC power supply.

Troubleshooting scenarios

Controller is Off

Power at Primary of Transformer, 0V at Secondary

the Power at Primary Transformer, 24V at

Secondary, 0V at Fuse/Breaker

and

Breaker/Fuse has tripped.

Possible Cause:

1.  Transformer is shorted.
2.  24VAC powered sensor is not wired with the same polarity as the controller.
3.  SA bus device is not wired with the same polarity as the controller.

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

Содержание FX-PCV1615































Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды

Johnson Controls FX-PCV1615, Руководство по установке

Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды