Johnson Controls FX-PCV1615 Скачать руководство пользователя страница 25

Страница: 25 / 30

Verification:

1. Measure the output and verify that it matches the command.
2. Disconnect the connected device and verify the commanded value is present.

LED table

Table 8: FX-PCV Controller status LEDs

LED label

LED color

Normal state

Descriptions of LED states

POWER

Green

On Steady

Off Steady = No power
On Steady = Power is supplied by

primary voltage

FAULT

Red

Off Steady

Blink - 2 Hz = Download or startup

in progress, not ready for normal

operation, SA Bus devices offline (such

as netsensors)
Rapid blink = SA Bus communications

issue
Off Steady = No faults
On Steady = Device fault or no

application loaded

SA BUS

Green

Blink - 2 Hz

Blink - 2 Hz = Data transmission

(normal communication)
Off Steady = No data transmission (N/A

- auto baud not supported)
On Steady = Communication lost;

waiting to join communication ring

ETH1

Green

Off

Off Steady = ETH1 is not connected
Blinking = ETH1 connected and

communicating

ETH2

Green

Off

Off Steady = ETH2 is not connected
Blinking = ETH2 connected and

communicating

Accessories

Use Table 9 to order accessories.

Table 9: FX-PCV1615/1626/1628/1630 Controller Accessories (Order Separately)

Product code number

Description

FX-PCX Series Expansion

Input/Output Modules

Refer to the

FX-PC Series Programmable Controllers and Related

Products Product Bulletin (LIT-12011657)

for a complete list of

available FX-PCX Expansion I/O Modules.

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

Содержание FX-PCV1615































Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды

Johnson Controls FX-PCV1615, Руководство по установке

Результаты поиска

Содержание FX-PCV1615

Отзывы:

Похожие инструкции для FX-PCV1615

Бренды по названию

Популярные бренды