JING JIE UniPBX-2000 Скачать руководство пользователя

Страница: 37 / 219

Using the System

The detail of each parameter is described as below:

Parameter Name

Description

No Answer Time Out

The default time to wait for the called party to answer.
The recommended value is 300.

Session Validation
Period

The time to check whether the call is still connected or
not. The default value is 3600 seconds which will
check the call around 30 minutes.

Session Validation
Target

The calling or called party will be checked for the call
existence. The default value is caller.

Session Validation
method

The SIP request method to be used for checking the
call existence. The default value is "Invite".

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды