JING JIE UniPBX-2000 Скачать руководство пользователя

Страница: 204 / 219

204

Modul
e

Level

Event

SIP

NOTICE

The IP x.x.x.x has been removed from blocking IP list.

SIP

NOTICE

SIP communication service NOTICE: (database
connection resumed)

SIP

NOTICE

01:35:47 (Registered) Extension: xxxx was registered
from x.x.x.x:5060 (x.x.x.x:5060)

SIP

NOTICE

SIP communication service NOTICE: (service started)

SIP

INFO

User ID: XXX call attempt had over the max concurrent
calls

SIP

INFO

Loop Detected: Calling: xxx from (x.x.x.x) to Called: xxx

SIP

INFO

Changes applied to the running system

RTP

NOTICE

Failed to create required sockets port=xxx

RTP

NOTICE

NAT resource service NOTICE: (service(v120206)
started)

RTP

INFO

Changes applied to the running system

RADIUS

WARN

Failed to start RADIUS service: (failed to bind required
sockets port:xxx)

RADIUS

WARN

Failed to start RADIUS service: (failed to get initial
parameters to start)

RADIUS

NOTICE

RADIUS service NOTICE: (service started)

RADIUS

INFO

Changes applied to the running system

RADIUS

WARN

Failed to receive response from RADIUS Server
[xxx.xxx.xxx.xxx].

RADIUS

NOTICE

Received RADIUS response from Server [xxx.xxx.xxx.xxx]

CRITICAL

This node is set to STANDBY mode by administrator. You
need activate it manually to rejoin the HA cluster.

CRITICAL

This node is failed-over to standby node (A/A mode).
Please check the system and reactive it.

CRITICAL

This node is failed-over to standby node (A/S mode) and
the system will start tried to clean-up.

CRITICAL

Resetting this node, because of no available note can be
failed over.

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды