JETWAY MI02 Series, Руководство пользователя

Страница: 31 / 41

27
►
Serial Port 3 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
*When set as
[Enabled]
, user can make further settings in the following items:
Change Settings
Use this item to select an optimal setting for super IO device.
For MI02 series with Q470, W480E and H420E chipset:
the optional settings:
[IO= 3F8h ; IRQ=10]; [IO=3F8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2F8h; IRQ=3, 4, 5, 7,
10, 11]; [IO=3E8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2E8h; IRQ=3, 4, 5, 7, 10, 11];
[IO=3E0h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2E0h; IRQ=3, 4, 5, 7, 10, 11].
For MI02 series with H420 chipset: the optional settings: [IO= 3E8h ; IRQ=10];
[IO=3F8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2F8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=3E8h;
IRQ=3, 4, 5, 7, 10, 11]; [IO=2E8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=3E0h; IRQ=3, 4, 5,
7, 10, 11]; [IO=2E0h; IRQ=3, 4, 5, 7, 10, 11].
► Serial Port 4 Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
The optional settings are: [Disabled]; [Enabled].
*When set as [Enabled] , user can make further settings in the following items:
Change Settings
Use this item to select an optimal setting for super IO device.
The optional settings: [IO=2E8h; IRQ=10]; [IO=3F8h; IRQ=3, 4, 5, 7, 10, 11];
[IO=2F8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=3E8h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2E8h;
IRQ=3, 4, 5, 7, 10, 11]; [IO=3E0h; IRQ=3, 4, 5, 7, 10, 11]; [IO=2E0h; IRQ=3, 4, 5,
7, 10, 11].
WatchDog Reset Timer
Use this item to enable or disable WDT reset function.
*When set as [ Enabled ], the following sub-items shall appear:
WatchDog Reset Timer Value
User can set a value in the range of [4] to [255].
WatchDog Reset Timer Unit
The optional settings are: [Sec.]; [Min.].
ATX Power Emulate AT Power
This item support Emulate AT power function, MB power On/Off control by power
supply. Use needs to select ‘AT or ATX Mode’ on MB jumper at first
(refer to
JAT_ATX
jumper setting for
Pin1&2 of
ATX Mode &
Pin 2&3 of A
T Mode Select)
Case Open Detect
Use this item to detect Case has already open or not. Show message in POST.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled] , system will detect if COPEN has been short or not (
refer
to
COPEN
jumper setting for Case Open Detection
); if Pin 1&2 of CASE OPEN
are short, system will show Case Open Message during POST.