Jet JTS-8, Руководство по эксплуатации

Страница: 2 / 19

4
Read and understand the entire
instruction manual before
attempting assembly or operation.
Keep this operating instruction
close by the machine, protected
from dirt and humidity, and pass it
over to the new owner if you part
with the tool.
No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this
case, protect the machine by
unplugging the mains cord.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit
- safety goggles
- ear protection
- dust protection
Do not wear gloves while operating
this machine.
For the safe handling of sawblades
wear work gloves.
Use suitable table extensions and
supporting aids for difficult to
handle or long work pieces.
Observe the chapter “save
operation” in this manual.
Check the correct rotation of the
sawblade before operating the
machine.
Do not start cutting operation until
sawblade is at full speed.
Do not use side pressure to stop
rotating blade.
Always hold and guide the work
pieces safely during machining.
Pay particular attention to
instructions on reducing the risk of
kickback.
The supplied raving knife must
always be used. Adjust the space
between raving knife and sawblade
teeth to be 2 to 5mm.
Do not perform operations for which
the tool has not been designed for,
e.g. do not use this table saw to cut
logs or firewood.
Insure that the work piece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to
handle work pieces.
Do not perform any operation
freehand.
Never reach around or over the saw
blade.
Always use the mitre gauge for
cutting off.
When ripping narrow work pieces
(smaller than 120mm) use as push-
stick or push-wood.
Push stick or push wood must stay
with the machine when tool is
stored and not in use.
Make sure that small cut off work
pieces will not be caught and
thrown away by the rising saw
blade teeth.
Remove cut and jammed work
pieces only when motor is turned off
and the machine is at a complete
standstill.
The use of dado-blades and groove
cutters is not permissible.
Install the machine so that there is
sufficient space for safe operation
and work piece handling.
Keep the inside of the cabinet clear
of sawdust and wood chips. Make
sure the motor fan and fan cover
are kept clear of sawdust.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be
placed stable on firm and levelled
ground.
Make sure that the power cord does
not impede work and cause people
to trip.
Never use the power cord to carry
the tool.
Do not expose the power cord to
heat, oil or any sharp corners.
Do not pull the cord to unplug.
If the tool is used outdoor, make
sure that the extension cord is rated
for outdoor use.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Pull the mains plug if the tool is not
in use.
Pull the mains plug prior to any
maintenance or a change of
accessory (e.g. sawblade).
Before starting the machine make
sure that operating and measuring
tools are removed from the
machine.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or
any medication. Be aware that
medication can change your
behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while
it is operating or running down.
Never leave a running machine
unattended.
Before you leave the workplace
switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire
alert options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can
also represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust
extraction device
Before machining, remove any nails
and other foreign bodies from the
work piece.
Specifications regarding the
maximum or minimum size of the
work piece must be observed.
Do not force the power tool. It will
do a better and safer job and give
you much better service if it is used
at the rate for which it was
designed.
Do not remove chips and work
piece parts until the machine is at a
complete standstill.
Never operate with the guards not
in place – serious risk of injury!
Do not stand on the machine.