Jepson 9435 T3, Руководство по эксплуатации

Страница: 11 / 124

EN
DE
FR
NL
ES
PT
PL
IT
Step 5
Premium Dry Cutter 9430: The face cover is attached
by turning it back to its original position and
replacing the screws (Figure 5).
Premium Super Dry Cutter 9435: Turn the small
cover back to its original position and tighten the
butterfly screw (Figure 5a-A). Move the vibration
dampers back to their original position by turning
them (figure 5a-C).
Step 6
Loosen the spindle lock and ensure that
the saw blade can rotate freely (Figure
6).
9.7. SAW BLADE GUIDES
Regularly spray the spots where the saw blade
comes into contact with the saw blade guides with
lubricating oil spray. Since the vibration dampers
are consumption parts, they should be replaced
when they are worn down by approx. 3 mm to a
residual value of 1 mm.
9.8. MAINTENANCE
Replacing the carbon brushes: (Figure 8 and 9)
1. Replace the carbon a brush when they are
worn down to approx. 1/4“ (6 mm) or spark
formation occurs. Both brushes must be
replaced at the same time.
2. Remove the worn brushes, insert the new
brushes and close the cover again.
The carbon brushes must be replaced
by an electrician!
9.9. MATERIALS
• Rust and acid-resistant steel (V2A) (Super Dry
Cutter)
• Mass structural steel (ST 33, ST 37-2, ST 52-3)
• Casting (SML Pipes)
• Water and gas pipes
• Angle bars, U profiles and double T profiles
• Plastic-encased pipes
9.10. CUTTING TECHNIQUE
Step 1: The circular cold saw can cut at angles of
45°-90°.
a) For 90°, position the work piece between the
clamping plate and the setting up piece and ensure
that the clamping fixture is tightened with the
clamping handle in clockwise direction.
b) For 45°, loosen the screw at the setting up piece,
set the machine to the desired angle and re-tighten
screws.
Next, insert the work piece and tighten the
clamping fixture firmly.
Step 2: On the handle, there is a safety switch
(Figure 10). In order to turn on the machine, push
the arm lock (A) simultaneously with the switch
handle (B). Only then, the handle can be moved
downwards.
Ensure that the motor runs load free for a few
seconds to reach the maximum operating speed
before you start sawing.
Step 3: Cut slowly and evenly. Lift the handle off the
work piece and release the switch to switch off the
saw. Release the handle only after the saw blade
comes to a total standstill.
9.11. CHIP BOX
The chip box (Figure 11/A) catches up to 80% of the
chips.
9.12. TRANSPORTING THE PREMIUM SUPER
DRY CUTTER
If you want to transport the Premium Super Dry
Cutter machine, keep the stopper handle (Figure
12/A) pulled outward and lower the operating arm
to the lowest position. Now let the stopper handle
engage.
You can now transport the device with the handle.
10. STANDARD EQUIPMENT
PDC 9430 T3:
1. Carbide tipped saw blade 60T
(305x1.8/2.2x25.4 mm) (Part no. 600530)
2. Hexagonal wrench and screwdriver
PSDC 9435 T3:
1. Carbide tipped saw blade 60T
(355x1.8/2.2x25.4 mm) (Part no. 600570)
2. Hexagonal wrench and jig plate
3. “K” clamping system (1209471)
10.1. OPTIONAL SAW BLADES &
ACCESSORIES PDC 9430T3
1. 80T carbide tipped saw blade for steel and
other materials (Part no. 600540)
2. 60T carbide tipped saw blade for steel and
other materials (Part no. 600530)
PSDC 9435 T3 | PDC 9430 T3
11