Jenn-Air JGCK424PS, Руководство пользователя

Страница: 5 / 32

5
INSTALLATION INSTRUCTIONS
REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Tools Needed
� Tape measure
�
Screwdriver
�
15/16" (24 mm) combination
wrench
� Pipe wrench
� Wrench or pliers
�
Marker or pencil
�
Pipe-joint compound
resistant to Propane gas
� Noncorrosive leak-detection
solution
Parts Supplied
� Gas pressure regulator
�
Burner grates
�
Burner caps
� Clamping brackets (4)
� 1 3 /
4
" (4.5 cm) clamping screws (2)
�
1/4" (0.6 cm) clamping screws (2)
�
Gasket
�
Flare Union Adapter
� Elbow/Union Adapter
� Sealing Tape
For Propane/Natural Gas Conversions
Tools Needed
�
Flat-blade screwdriver
�
T20
®
TORX
®
✝ screwdriver
�
Wrench
� 7.0 mm nut driver
� Masking tape
Parts Supplied
�
Propane injector package
�
Conversion instructions
�
Conversion label
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See “Electrical Requirements” and
“Gas Supply Requirements” sections.
NOTE: Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
Location Requirements
Mobile Home Installation
The installation of this cooktop must conform to the Manufactured
Home Construction and Safety Standards, Title 24 CFR, Part
3280 (formerly the Federal Standard for Mobile Home
Construction and Safety; Title 24 HUD part 280); or when such
standard is not applicable, the Standard for Manufactured Home
Installations (Manufactured Home Sites, Communities and
Setups), ANSI A225.1 - latest edition, or with local codes.
In Canada, the installation of this cooktop must conform with the
current standards CAN/CSA-Z240 - latest edition, or with local
codes.
IMPORTANT
� For solid surface material installations such as Surel ™ and
Corian ® , consult with solid surface manufacturer. Apply heat
reflective tape such as Scotch ® Aluminum Foil Tape #425 or
#427 around the cutout so that it folds over on the top and
sides.
� Do not wrap the tape underneath the cooktop.
� Be sure the tape extends beyond the outermost flange of the
cooktop. All corners should be covered with tape.
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
�
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located on the underside of the
cooktop base.
A.
Model/serial/rating plate
�
The cooktop should be installed in a location away from strong
draft areas, such as windows, doors, and strong heating vents
or fans.
�
All openings in the wall or floor where cooktop is to be installed
must be sealed.
�
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
� Grounded electrical supply is required. See the “Electrical
Requirements” section. Proper gas supply connection must be
available. See the “Gas Supply Requirements” section.
�
The cooktop is designed to hang from the countertop by its
side or rear flanges.
� The gas and electric supply should be located as shown in the
“Cabinet Dimensions” section so that they are accessible
without requiring removal of the cooktop.
� Provide cutout in right rear corner of cutout enclosure as
shown to provide clearance for gas inlet, power supply cord,
and to allow the rating label to be visible.
IMPORTANT: To avoid damage, check with your builder or
cabinet supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
✝
TORX
®
and T20
®
are registered trademarks of Acument Intellectual Properties, LLC.