background image

ii

Notice

Every  effort  was  made  to  ensure  that  the  information  in  this  document  was  accurate  at 
the time of printing. However, information is subject to change without notice, and JDSU 
reserves the right to provide an addendum to this document with information not available 
at the time that this document was created.

Copyright

©  Copyright  2009  JDSU,  LLC.  All  rights  reserved.  JDSU,  Enabling  Broadband  and  Optical 
Innovation, and its logo are trademarks of JDSU, LLC. All other trademarks and registered 
trademarks  are  the  property  of  their  respective  owners.  No  part  of  this  guide  may  be 
reproduced  or  transmitted  electronically  or  otherwise  without  written  permission  of  the 
publisher.

Trademarks

JDSU is a trademark of JDSU in the United States and other countries.
CleanBlast is a registered trademark of JDSU.
RibbonDrive is a trademark of JDSU.
Hirose is a trademark of Hirose Electric Group.
MTP is a registered trademark of US Conec, Ltd.
IBC is a trademark of US Conec, Ltd.
Molex is a registered trademark of Molex Incorporated.
OptiTip and OptiTap are trademarks of Corning Incorporated.
Sony is a registered trademark of Sony Corporation.
Specifications, terms, and conditions are subject to change without notice. All trademarks 
and registered trademarks are the property of their respective companies.

Patents

RibbonDrive Tips: US Patent No. 6,751,017 / 6,879,439
CleanBlast: US Patent No. 7,232.262

Tested Equipment

All  pre-qualification  tests  were  performed  internally  at  JDSU,  while  all  final  tests  were 
performed  externally  at  an  independent,  accredited  laboratory.  This  external  testing 
guarantees  the  unerring  objectivity  and  authoritative  compliance  of  all  test  results. 
JDSU's Commerce and Government Entities (CAGE) code under the North Atlantic Treaty 
Organization (NATO) is 0L8C3.

FCC Information

Electronic test equipment is exempt from Part 15 compliance (FCC) in the United States.

European Union

Electronic  test  equipment  is  subject  to  the  EMC  Directive  in  the  European  Union.  The 
EN61326  standard  prescribes  both  emission  and  immunity  requirements  for  laboratory, 
measurement, and control equipment. This unit has been tested and found to comply with 
the limits for a Class A digital device.

Independent 

Laboratory Testing

This unit has undergone extensive testing according to the European Union Directive and 
Standards.

Содержание CleanBlast FCL-P1005





























Отзывы: