background image

Jason International, Inc.  •  

 

501.771.4477  

    

Page 1 of 17

    

Customer Service :  800.255.5766 

Copyright © 2013 Jason International.

“TO BE REMOVED FOR USE BY THE OCCUPANT.”

49-1010-800

Date   02/13

Owner’s Manual

forma

®

 and Designer Microsilk

®

-airMasseur

®

 Baths

InsTallaTIOn, OPeraTIOn, anD MaInTenanCe

Jason International, Inc.

 

8328 MacArthur Drive

North Little Rock, AR 72118-2029

www.jasoninternational.com

Owner’s reCOrD

Dealer: 

Date Purchased: 

Date Installed: 

Installer: 

PlaCe serIal nuMBer CarD wITh 

PrODuCT COnfIguraTIOn In ThIs BOx

InsPeCTIOn

Inspect the unit prior to installation. In the event of a 

problem, DO NOT install the unit.

  

All components are factory assembled to the bath and the 
unit is water tested and inspected prior to leaving Jason 
International, Inc.

If the carton shows sign of damage, inspect the product 
before accepting and describe the problem on the  
Bill of Lading.

NOTe: Transportation and insurance from Jason’s 

factory are the buyer’s responsibility.

Damage sustained in transit is the responsibility of 

the carrier.

 If damage is discovered, the carrier must 

be immediately notified in writing with a request for a 
representative to inspect the unit. Failure of the carrier 
to respond should be reported to the seller and carrier. 
Always file a freight claim promptly.

The installer is responsible for ensuring that the unit is 
free from defects or shipping damage. 

In the event of a 

problem, DO NOT install the unit. 

Jason International is not responsible for damage that 
might have been avoided by inspection or testing prior to 
installation.

If the carton shows sign of damage, inspect 

the product before accepting and describe the 

problem on the Bill of lading.

Damage to the unit during installation will not be covered 
by warranty and is the responsibility of the installer.  

ALL WARRANTY CLAIMS ON ACRYLIC SURFACe 

DAMAGe MUST Be MADe PRIOR TO INSTALLATION. 

Inspect plumbing and bath surface for missing or damaged 
components. Alert your dealer of any discrepancies.

To protect the unit from damage, keep the bath in the 
carton until ready for installation.

eQuIPMenT aCCess

In accordance with Building Codes, service access to 
all hydrotherapy bath equipment, controls and electrical 
connections must be provided during installation 

(Recommended minimum 28" x 17" [71 x 43 cm]). 

Insufficient access will hinder repair and maintenance. 
Warranty service will not cover costs of providing 
equipment access.

Jason offers an optional removable lateral skirt for all 
rectangular baths. The skirts are available in matching 
acrylic colors and provide convenient access to bath 
equipment, as well as an excellent finished appearance.

The Specification Sheet for this bath contains additional 
technical information.  This sheet can be provided by your 
dealer or accessed online at 

www.jasoninternational.com

.

Содержание Forma MicroSilk-AirMasseur


















Отзывы: