Japan Cach Machine TAIKO Series Скачать руководство пользователя страница 7

Страница: 7 / 87

TAIKO Service Manual

eface

Documentation Conventions

The list below describes the documentation convertions used in this manual.

Icon/Mark

Descriptions

This icon indicates important information or procedures that must be
followed for correct and risk-free unit operation.

This icon indicates useful or recommended supplemental
information.

1. 2….

This indicates steps in a procedure. Be sure to perform these steps
in the order given.

See=>

This indicates related information to refer.

This indicates useful or important supplemental inforamation

RoHS Compliance

The TAIKO

(PUB-7/PUB-11)

is a RoHS Compliant products. The following six kind of

hazardous substances restricted by RoHS are NOT contained in the TAIKO unit.

nRestricted Hazardous Substances

- Plumbum
- Mercury
- Cadmium
- Chromium Hexavalent
- PBB
- PBDE

- All brand names and product names are trademarks or regis-

tered trademarks of their respective companies.

Содержание TAIKO Series























































































Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды

Japan Cach Machine TAIKO Series, Руководство по обслуживанию

Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды