Japan Cach Machine TAIKO Series Скачать руководство пользователя страница 32

Страница: 32 / 87

TAIKO Service Manual

2-14

CHAPTER

*1 For details about the Test Mode, refer to 5-3. Test Mode.
*2 The acceptance rate will be improved but operation time will be increased if a

banknote is rejected.

*3 Fishing prevention will be improved but operation time will be increased.
*5 For Details about demomination Stting “INHIBIT”/”ACCEPT”, refer to the Soft-

ware Information Sheet.

2-5-2. Basic Settings
01: ID-001 (parallel) Specification

SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8

Accept Setting

OFF OFF OFF OFF

OFF OFF

Inhibit Setting

OFF OFF OFF OFF

OFF

Define Pattern 1

OFF OFF OFF OFF

OFF

Define Pattern 2

OFF

OFF OFF OFF

OFF

OFF OFF

OFF OFF OFF OFF OFF

Adjustment Mode *1

Denomination

Setting Mode
LED Pattern

Setting Mode

Setting Items

Download Mode *1

Encryption Code Initializing

Setting Mode

OFF

Test Mode*1

Normal Mode

Escrow Mode

No Escrow Mode

Double‑Scan Mode*2

Normal Scan Mode

Five (5) drum cycles (fishing prevention)*3

Normal Operation

Denomination Setting "INHIBIT"*4

Denomination Setting "ACCEPT"*4

Denomination Setting "INHIBIT"*4

Denomination Setting "ACCEPT"*4

Denomination Setting "INHIBIT"*4

Denomination Setting "ACCEPT"*4

Denomination Setting "INHIBIT"*4

Denomination Setting "ACCEPT"*4

SW#

Setting Item

2-5-3. Special Settings

For details about Software Download and Adjustment, refer to Chapter 4 Down-
load/Adjustment.

Содержание TAIKO Series























































































Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды

Japan Cach Machine TAIKO Series, Руководство по обслуживанию

Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды