Japan Cach Machine TAIKO Series Скачать руководство пользователя страница 57

Страница: 57 / 87

5-3

TAIKO Service Manual

CHAPTER

Symptom/Error Message

Possible Causes

Recovery Action

Acceptor is not working.

(Acceptor does not accept

any bills.)

Entrance Sensor is not
working or there is any
foreign object at the
entrance.

Remove the foreign object and clean
the entrance sensor. See=> 5-4.
Cleaning
Perform Aging. See=>

5-3-5

. Aging

details
If any sensor error is found, replace
the CPU/Sensor board. See=>
Chapter 6 Replacement Procedure

Feed or Pinch roller is
spoiled with dirt or broken.

Clean the feed or Pinch roller. See=>

5-4

. Cleaning

If any corruption is found, replace it.
See=>

6-4

. Replacement of Sensor

Board

and 7-2. TAIKO(PUB-

7/PUB-11) Unit

Feed or Pinch roller spring is
missing or loose.

Verify the condition of the Feed or
Pinch roller spring

by pressing with

fingertips

and replace it as required.

See=> 7-2. TAIKO(PUB-7/PUB-11)
Unit

There is any foreign objects
is on the transport path.

Remove the foreign objects from the
transport path and clean. See=> 5-4.
Cleaning

Faceplate does not match
with the bill width.

Change the faceplate guide depending
on the bill width. See=>

3-1

Installation/Removal

The bill width is 83mm or
larger or 62mm or less.
(Out of TAIKO
Specifications)

Use the only acceptable bills. See=>
Chapter 2 Specifications

Rollers, belts and lenses is
soiled with dirt.

Clean the rollers, belts and lenses.
See=> 5-4. Cleaning

Sensor needs to be adjusted.

Adjust the TAIKO unit. See=>

4-2.

Adjustment

After disassembled, the
TAIKO has not been
adjusted.

Adjust the TAIKO unit. See=>

4-2.

Adjustment

The software revision is old.

Download the latest software program.
See=> 4-1. Download

The bill that software
program is not supported is
inserted.

Verify if the denomination, issued year
is appropriate in the software
information sheet.

JAM bill occurs often.

Acceptance rate is low.

Содержание TAIKO Series























































































Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды

Japan Cach Machine TAIKO Series, Руководство по обслуживанию

Результаты поиска

Содержание TAIKO Series

Отзывы:

Похожие инструкции для TAIKO Series

Бренды по названию

Популярные бренды