Japan Cach Machine TAIKO Series Скачать руководство пользователя страница 13

Страница: 13 / 87

1-3

TAIKO Service Manual

CHAPTER

1-2. Prior to Use

Be sure to follow these steps when creating the project for TAIKO unit.

1. Preparation

Before using TAIKO unit, check the all required hardware is present and read all
specification, wiring, and installation information.

See => Chapter 2 Specifications or Chapter 3 Installation/Operation

2. Panel Cut Out

Creat the panel cut out on the door to install the TAIKO unit.
See =>

3-1. Installation / Operation

3. Setting

Set the DIP switch depending on the connected machine or the features of TAIKO unit
you want to use.
See =>

2-5. DIP Switch Settings

4. Installation

Install the TAIKO unit and connect the harness with the mashine.
See=> Chapter 2 Specifications, or Chapter 3 Installation/Operation

5. Operation

Turn on the power to the TAIKO unit.

Содержание TAIKO Series























































































Результаты поиска

Содержание TAIKO Series

Отзывы:

Japan Cach Machine TAIKO Series, Руководство по обслуживанию, Страница: 13 / 87

Результаты поиска

Содержание TAIKO Series

Отзывы: