Janz Tec emPC-CXR Скачать руководство пользователя страница 15

Страница: 15 / 47

emPC-CXR

(

Hardware Manual

)

•

Installation

3 - 13

Rev. V1.2

Janz Tec AG

3.2.3

Ethernet Interfaces LAN1 and LAN2

Ethernet interfaces of the motherboard. The Ethernet physics is 10/100/1000BaseT, available through
the shielded M12 connectors.

3.2.4

USB 2.0 Host Interfaces USB1 and USB2

2 USB 2.0 host interfaces are available through 4 pin M8 female connectors.

The USB connectors do not provide standby power, thus wake on USB is not possible.

3.2.5

CAN

If the product is equipped with CAN interface(s), 5 pin A-coded M12 female connectors are equipped
for the CAN.

15 pin female HD-Sub

1 Red

9 +5V

2 Green

10 GND

3 Blue

11 N/C

4 N/C

12 DDC Data

5 GND

13 HSync

6 GND

14 VSync

7 GND

15 DDC Clock

8 GND

table 2: VGA connector

8 pin female M12 X-coded

1 MDI0+

5 MDI3+

2 MDI0-

6 MDI3-

3 MDI1+

7 MDI2+

4 MDI1-

8 MDI2-

table 3: Ethernet connector

4 pin M8

1 +5V (red)

2 USB- (white)

3 GND (black)

4 USB+ (green)

table 4: USB connector with USB cables colour codes

5 pin female M12 A-coded

1 NC

2 NC

3 GND-CAN

4 CAN-H

5 CAN-L

table 5: M12 CAN connector

Содержание emPC-CXR
















































Результаты поиска

Содержание emPC-CXR

Отзывы:

Похожие инструкции для emPC-CXR

Бренды по названию

Популярные бренды

Janz Tec emPC-CXR, Руководство по оборудованию

Результаты поиска

Содержание emPC-CXR

Отзывы:

Похожие инструкции для emPC-CXR

Бренды по названию

Популярные бренды