Janz Tec emPC-CXR Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 47

Janz Tec emPC-CXR Скачать руководство пользователя страница 13

emPC-CXR

(

Hardware Manual

)

•

Installation

3 - 11

Rev. V1.2

©

Janz Tec AG

3.2

Connectors and Operators

Below the VGA connector you find an M5 thread for an additional earth connection. EMI Tests were
passed without extra earth connection. However, during EMI testing, earth connection was established
with the shields of the IO cables (VGA, LAN, …).

The green power LED between the USB connectors lights when the system is running. It does not
light when the system is in power down mode even if power is applied at the power connector.

NOTICE

Do not actuate connectors when power is applied.

NOTICE

All connectors (M12/M8/DSUB) are not sealed when no mating connector is present. Use
a screw plug to seal unused connectors.

NOTICE

Mechanical actuation of M12/M8 connectors is prohibited below -25 °C.

LAN1

LAN2

POWER

CAN/Serial 2

Digital IO

CAN/Serial 1

USB1

USB2

figure 3: front view with connectors

«
...
11
12
13
14
15
...
»

Содержание emPC-CXR
















































Отзывы:

Нет отзывов