Janz Tec emPC-CXR Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 47

Janz Tec emPC-CXR Скачать руководство пользователя страница 11

emPC-CXR

(

Hardware Manual

)

•

Installation

3 - 9

Rev. V1.2

©

Janz Tec AG

3

Installation

CAUTION

The product is designed as a fan less computer system. Nevertheless a certain amount
of heat is generated inside the housing. The housing transports this heat to the
environment.

Caution when touching the housing, burns hazard

!

The product can be operated with DC power supply from 9 to 34 V.

3.1

Mounting

The emPC-CXR is intended to be mounted on a flat surface wall.

NOTICE

The product must be mounted exactly as indicated in figure 2 to allow the required
natural heat transfer. Derivations of < 5 ° do not matter.
The indicated area must be free of obstacles which prevent heat transfer.
There should be no space between the wall and the product (use no spacers for
mounting).

55mm

55mm

100mm

100mm

Above

Below

Left

Right

Front

Above

Below

Cool-Air

Hot-Air

Wall

figure 2: Mounting guidelines

«
...
9
10
11
12
13
...
»

Содержание emPC-CXR
















































Отзывы:

Нет отзывов