Page 24
6.3
Glossary of Controller Messages
CLEANER CANNOT BE TURNED ON WHILE SPA IS ON -
This message is displayed if the pool cleaner is activated
when in spa mode (i.e., water is circulating to spa). The pool cleaner requires that water be circulating to the pool in order for it to
operate. Return to pool mode to activate the cleaner.
CLEANER CANNOT BE TURNED ON WHILE SPILLOVER IS ON -
The return valve has been rotated to the spa position
to give the spa spillover effect.
FREEZE PROTECTION ACTIVATED -
This message indicates that freezing conditions have been detected by the freeze
protection sensor, and that equipment assigned to freeze protection (for example, lter pump) are active. See the section on freeze
protection on page 16 of this manual for more information. (
NOTE:
Only the lter pump is protected unless the optional freeze
sensor is installed.) If a freeze protected Auxiliary is turned off during freeze protection, a message will scroll indicating that item
is off but will turn on in X amount of minutes. The minutes will vary depending on how long freeze mode has been active from 1
to 15 minutes.
SENSOR OPENED -
This error message indicates that the sensor is not installed properly or is malfunctioning. Call your pool
service person to resolve this problem.
NOTE:
If the message reads WATER SENSOR OPEN, the heater will not re. If message
AIR SENSOR OPEN is displayed, freeze protection will not operate correctly.
POOL HEATER ENABLED -
This message indicates that the pool heater is ready to use but is not actually ring. The lter
pump must be on, and the water temperature must be below the setting for the heater to re.
PUMP WILL REMAIN ON WHILE SPILLOVER IS ON -
This message is displayed when you attempt to turn off the lter
pump while a spa spillover is on. Since the lter pump is necessary for spillover operation, the pump will remain on until the
spillover is turned off.
PUMP WILL TURN OFF AFTER COOL DOWN CYCLE -
This message indicates that the lter pump is circulating water to
cool down the heater. The lter pump will continue to run for ve minutes to protect the heater from damage, whenever the heater
has red and has been off for less than ve (5) minutes.
PUMP WILL TURN ON AFTER DELAY -
This message is displayed during pool/spa switching. The AquaLink
®
RS waits 35
seconds while the valves turn from pool position to spa position (or vice-versa) before activating the lter pump.
SERVICE MODE IS ACTIVE -
This message indicates that the Controller has been locked out from the power center and is
not operational. Service mode is used by the pool service person to aid them in servicing the pool. The Controller will not be
functional until the switch at the Power Center is moved back to AUTO mode.
SENSOR SHORTED -
This error message indicates that the sensor is not installed properly or is malfunctioning. Call your pool
service person to resolve this problem.
NOTE:
If the message reads WATER SENSOR SHORTED the heater will not re. If the
message AIR SENSOR SHORTED is displayed, freeze protection will not operate correctly.
SPA WILL TURN OFF AFTER COOL DOWN CYCLE -
When the system is in Spa Mode (water is circulating to the spa) and
the Spa button is pressed to switch water circulation to the pool, the system will not switch to Pool Mode for ve (5) minutes, and
will continue to circulate the water (if the heater has red and has been off for less than ve minutes). This delay allows water to
cool the heater down by circulating water through it, preventing equipment damage.
TIMED AUX ON, WILL TURN OFF AFTER 30 MINUTES -
This message indicates that a timed auxiliary (usually a blower)
has been activated and will turn off after 30 minutes. Some labels (for example, blower, ll line) have a built-in 30 minute shut
off.
TIMEOUT MODE IS ACTIVE -
This message indicates that the Controller has been locked out from the Power Center and is
not operational. TIME OUT mode is used by the pool service person to aid them in servicing the pool. The Controller will not be
functional for three hours, or until the switch at the Power Center is turned back to AUTO mode.
SPILLOVER IS DISABLED WHILE SPA IS ON -
This message is displayed when the spa spillover is pressed while in spa
mode (water circulation is to spa). The spillover requires that water circulation is to pool in order to operate. The spillover will
activate when the system switches back to pool mode.
