JAI IIT Camera Systems VIS-CAM 350 Скачать руководство пользователя | Manualshive

Страница: 16 / 44

background image

IIT Camera System Manual

16

Installation Preparation

Figure 6.

Typical Over Lane Site Layout Plan

The Light Sensor and Flash shown in Figure 6 are optional.

If over lane mounting is not possible the camera can be mounted at the side of the road as close to

the road as possible.

2.2

Performance of Trigger and Light Sensor function

As mentioned in section 2.1.1 the performance of the camera is dependent on respecting

installation parameters. These performance conditions have influence on both the trigger and the
light sensor function.

Various weather caused conditions may also influence the performance. A wet license plate has less
retro-reflectance than a dry one and the same applies if it is covered with dirt or snow. Some

license plates have reduced retro-reflectance due to wear and tear.

«
...
14
15
16
17
18
...
»

Содержание IIT Camera Systems VIS-CAM 350













































Отзывы:

Нет отзывов

Похожие инструкции для IIT Camera Systems VIS-CAM 350

Бренд: Hama Страницы: 60

Бренд: wanscam Страницы: 19

Lorex LNC250 PING Series

Бренд: FLIR Страницы: 2

TempControl HTA-100

Бренд: Symmons Страницы: 4

Бренд: Edimax Страницы: 2

Бренд: Vivotek Страницы: 2

thombox Security pack

Бренд: THOMSON Страницы: 8

Бренд: LINNEPE Страницы: 7

Бренд: Zavio Страницы: 16

Бренд: V2 Страницы: 12

Бренд: Brickcom Страницы: 7

Vision WV-8S-180-AI

Бренд: wavestore Страницы: 12

Бренд: COMPOLOGY Страницы: 4

Бренд: SALIX Страницы: 12

Бренд: Ganz Страницы: 12

Бренд: minrray Страницы: 15

Бренд: SOWZE Страницы: 6

SYSTEM MASTER PC4000

Бренд: DSC Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды