JAI IIT Camera Systems VIS-CAM 350 Скачать руководство пользователя | Manualshive

Страница: 36 / 44

background image

IIT Camera System Manual

36

Appendix D

7

Appendix C: VIS-CAM 400 IIT-2030 and VIS-CAM 400 IIT-2076

The VIS-CAM 400 IIT-2030 and VIS-CAM 400 IIT-2076 are made a little different from the VIS-CAM 350

IIT cameras. The picture below shows the VIS-CAM 400 IIT overview

Figure 34.

VIS-CAM400IIT-2030 and VIS-CAM400IIT-2076 overview

Note: The TS-9725EN camera is not powered. Only fiber front is exploited. Do not adjust the

mechanical mount for this camera.

The fiber assembly in the IIT cameras is made from 8 x 1mm fibers giving a total width of 8mm. This

coverage fits the 2/3” CCD fine in the TS-9725EN and TS-1335EN (VIS-CAM350IIT) cameras having a
sensor width of 8.8mm.

The width of the sensors in the TS-2030EN and the TS-2076EN, used in VIS-CAM400, is 14.2mm and
the fiber assembly is too small to cover the width of this sensor. A solution using two cameras has

therefore been chosen where the trigger unit is a TS-9725EN camera. Only the fiber front of this
camera is exploited and the camera does not need to be powered except when alignment is

performed at factory. The TS-9725 camera is mounted with a 25mm lens and the TS-2030EN/TS-
2076EN with a 35mm lens giving almost the same field-of-view for the two cameras.

Having the camera and trigger unit separated this way, makes it possible to adjust the trigger-line

within the picture height, to some degree, by adjusting the camera mount inside the housing. As for
the single camera version, the camera with the fiber front, may not be adjusted. This has been

done from the factory to cover the IR illuminated area.

Please see appendix E regarding connection of floodlight for VIS-CAM 400 IIT.

Apart from the described differences, the setup and configuration is the same as the single camera
version.

«
...
34
35
36
37
38
...
»

Содержание IIT Camera Systems VIS-CAM 350













































Отзывы:

Нет отзывов

Похожие инструкции для IIT Camera Systems VIS-CAM 350

540EZ - Speedlite - Hot-shoe clip-on Flash

Бренд: Canon Страницы: 4

Бренд: Ultrative Страницы: 9

Бренд: 3xLogic Страницы: 25

VX-2A-B-IWD (R)

Бренд: 3xLogic Страницы: 80

Бренд: Wansview Страницы: 2

MagnaLatch ALERT

Бренд: D&D Technologies Страницы: 2

Бренд: DAGE-MTI Страницы: 16

Бренд: NA-DE Страницы: 7

Бренд: Digisol Страницы: 18

Бренд: CP Electronics Страницы: 4

Бренд: MasterCool Страницы: 3

FireClass FC400H

Бренд: Bentel Страницы: 4

Бренд: NAVAC Страницы: 4

Бренд: Iget Страницы: 8

Бренд: Foscam Страницы: 70

Бренд: Ziton Страницы: 13

Бренд: Abus Страницы: 2

Бренд: Zhejiang Uniview Technologies Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды