JAI IIT Camera Systems VIS-CAM 350 Скачать руководство пользователя | Manualshive

Страница: 14 / 44

background image

IIT Camera System Manual

14

Introduction

Vehicles are detected from both driving directions (front or rear shots).

The system will only work

if the license plate is moving through the retro-reflective sensitive region of the picture area.

Other parts of the vehicle being retro-reflective can cause generation of triggers. These parts can
be the tail light or stickers of different kinds.

Besides the special IIT functions, many of the I/O Board functionalities from VIS-CAM 300/350/400
are available. This includes output for camera heater, output for external flash and 24V auxiliary

output.

If only the IIT trigger functionality is used (excluding the internal light sensing feature), the camera

can be mounted together with an external light sensor. For details regarding Light Sensor
positioning and configuration, please refer to VIS-CAM System Installation manual.

The J-Panel (Junction Panel) described in the VIS-CAM System Installation manual is also applicable
in conjunction with the IIT camera.

«
...
12
13
14
15
16
...
»

Содержание IIT Camera Systems VIS-CAM 350













































Отзывы:

Нет отзывов

Похожие инструкции для IIT Camera Systems VIS-CAM 350

540EZ - Speedlite - Hot-shoe clip-on Flash

Бренд: Canon Страницы: 12

Бренд: Panamalar Страницы: 32

Бренд: NELLYS SECURITY Страницы: 15

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

Digiplex EVO DGP2-640

Бренд: Paradox Страницы: 24

Бренд: ACTi Страницы: 19

Бренд: ACTi Страницы: 19

Бренд: ADT Страницы: 29

PIH-0364X WN IP

Бренд: Lilin Страницы: 29

NVAHD-2DN3201MH/IR-1-PIR

Бренд: Novus Страницы: 32

GLASS BREAK DETECTOR

Бренд: Tattletale Страницы: 2

Бренд: Speco Страницы: 104

Бренд: media-tech Страницы: 2

Бренд: Idis Страницы: 51

DH-IPC-HFW5421E-Z

Бренд: Zhejiang Страницы: 14

Бренд: Sennheiser Страницы: 2

Бренд: Olympus Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды