JAI AB-200CL Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 69

background image

AM-200CL / AB-200CL

- 6 -

Before using AM-200CL and AB-200CL

The CCD sensor used in the AM-200CL and AB-200CL

operates with four (4) taps or two(2) taps, and

a 40MHz pixel clock. However, the video output through the Camera Link

®

interface is 2 taps for

monochrome and Bayer color modes, and 1 tap for monochrome , Bayer color modes and RGB color
output.
Accordingly, the pixel clock at the Camera Link interface is 80MHz and users should make sure that
the specifications and performance of connected frame grabber boards and PCs can support this
clock speed. The maximum length of the Camera Link cable may also be impacted.

The AM-200CL and AB-200CL are high resolution and high frame rate cameras with 1600(h) x 1200(v)
pixel resolution and a 68fps frame rate for 2 tap output or a 34fps frame rate for 1 tap output.

Accordingly, the amount of data produced is very large. If the output is set at 10-bits or 12-bits per
pixel, the total data stream is approx. 2.0 Gbit/sec. as a 16-bit process in the frame grabber board.
A frame grabber board connected to the PCI-32bit bus has a bandwidth of 2.1 Gbits/sec.
This is almost the limit of bandwidth and in this case, it is recommended to use the PCI-64bit bus or
to use a frame grabber board that can utilize the PCI Express Bus x 8.

JAI recommends using a PC with CPU better than i7.

«
...
6
7
8
9
10
...
»

Содержание AB-200CL






































































Отзывы:

Нет отзывов

Похожие инструкции для AB-200CL

Бренд: Xiaomi Страницы: 10

Бренд: Siqura Страницы: 2

Бренд: Care Call Страницы: 2

Бренд: Iget Страницы: 2

Бренд: OEM Optical Страницы: 25

Бренд: Alecto Страницы: 76

Бренд: ADT Страницы: 14

Бренд: Feig Electronic Страницы: 12

FlexPower VNC4030-111PAS

Бренд: Arlo Страницы: 2

Бренд: Baldwin Boxall Страницы: 7

HomeGuard HGDVK-84404

Бренд: Iget Страницы: 7

Бренд: Neostar Страницы: 2

Бренд: Innotech Страницы: 24

Бренд: Surveon Страницы: 116

Бренд: ANALOX Страницы: 16

Бренд: schmersal Страницы: 10

Binswitch Elite BSE1V10C

Бренд: 4B Страницы: 12

Бренд: Elmes Electronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды