JAI AB-200CL Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 69

background image

AM-200CL / AB-200CL

- 32 -

7.6. Timed mode (so-called EPS operation)

This mode allows a single image frame to be captured with a preset exposure time by using
the external trigger. Additional settings determine if the trigger pulse can be accepted
during the exposure period.

The frame rate of full pixels readout is 68fps for 2 tap output and 34.2fps for 1 tap output.

Primary settings to use this mode

Sensor Digitization Taps: SDT= 0 (Two taps) SDT=1 (One tap)

Acquisition control

Acquisition frame rate:

AR= 1

～

42964

Exposure control

Exposure mode:

EM=1 (Timed)

Exposure time: PE=10

μ

s

～

2000000

μ

s

Trigger control

Trigger mode:

TM=1 (ON)

Trigger overlap:    TO=0 (OFF) or 1=(Readout)
                                OFF: LVALsync    Readout: LVALsync/async automatic setting
Trigger source:      TI=0 (Camera Link, default)

or 1 (Hirose 12-pin)

Trigger Activation: TA=0 (Rising edge), 1=

（

Falling edge

）

Note

：

The AM-200CL and AB-200CL prioritize the frame rate over the exposure time. If the

exposure time is set at longer than 15.56ms (1 frame period), the frame rate must

be increased so that it is longer than the exposure time.

Minimum interval of the trigger pulse

2 tap output

FULL

2/3 AOI 1/2 AOI 1/4 AOI 1/8 AOI

Minimum frame line

613

463

388

275

219

1 tap output

FULL

2/3 AOI 1/2 AOI 1/4 AOI 1/8 AOI

Minimum frame line

1221

921

771

546

434

Note: The read out area for each AOI is the centered readout (same lines for upper and
lower)

«
...
32
33
34
35
36
...
»

Содержание AB-200CL






































































Отзывы:

Нет отзывов

Похожие инструкции для AB-200CL

EF35mm f/2 IS USM

Бренд: Canon Страницы: 2

EF300mm f/2.8L IS II USM

Бренд: Canon Страницы: 13

EF28-135mm f/3.5-5.6 IS USM

Бренд: Canon Страницы: 9

Multi Gas Clip Simple Plus

Бренд: Gas Clip Technologies Страницы: 20

Бренд: ZMODO Страницы: 2

Бренд: U-Prox Страницы: 29

Бренд: Samsung Страницы: 1

Бренд: IFM Страницы: 9

Бренд: nclebo Страницы: 20

Бренд: Eurotops Страницы: 12

QC804-261-1 NVR

Бренд: Q-See Страницы: 11

Бренд: Rohm Страницы: 9

Бренд: Denver Страницы: 12

Бренд: Observint Страницы: 23

Бренд: NAPCO Страницы: 16

Бренд: United Security Products Страницы: 16

Бренд: Moore Industries Страницы: 46

Бренд: Camlux Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды