Jackson DishStar HT Скачать руководство пользователя страница 17

Страница: 17 / 68

07610-004-37-13-E

To change the value of a parameter, use the MOVE button to illuminate the light next

to the time option (time is measured in seconds). In the time categories, each second

in use will light up. To deselect the option, press ENTER and the light will go off, press

ENTER again and it will illuminate. Once you have set your time category, press the

MOVE button until the ACCEPT light illuminates and press ENTER. This will save the

changed parameters and exit the programming mode.

To change any other values, you will have to return to the programming mode. To

revert back to a previous setting, you must return to that option and change the

parameter back to the previous setting.

Once in the programming mode, if there have been no keypad inputs for approximately

two minutes, the system will automatically exit out of the programming mode. Any

changes to parameters will be lost when the programming mode is automatically

exited.

The wash and drain cycles are not adjustable.

All time adjustments are in seconds. Refer to the chart below for adjustable outputs.

TIMER PROGRAMMING BOARD

PGM

TIME IN SECONDS

0.8

0.4

0.2

0.1

MOVE

ENTER

PROGRAMMING

CHEMICAL

FEEDER PUMPS

PGM

DishStar

LT/LT-H

Not adjustable

Rinse-Aid

Rinse

Fill

Detergent

Sanitizer

Rinse-Aid

Detergent

INSTRUCTIONS

INSTALLATION

Содержание DishStar HT





































































Результаты поиска

Содержание DishStar HT

Отзывы:

Похожие инструкции для DishStar HT

Бренды по названию

Популярные бренды

Jackson DishStar HT, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DishStar HT

Отзывы:

Похожие инструкции для DishStar HT

Бренды по названию

Популярные бренды