Jackson DishStar HT Скачать руководство пользователя страница 11

Страница: 11 / 68

07610-004-37-13-E

All electrical ratings provided in this manual are for reference

only. Always refer to the machine data plate to get exact electrical

information for this machine.

All electrical work performed on

machines should be done in accordance with applicable

local, state, territorial, and national codes.

Work should only

be performed by qualified electricians and authorized service

agents.

Note that all electrical wiring used in the DishStar

series of

machines must be rated, at a minimum, for 212 °F (100 °C), and

that only copper conductors must be used.

Where applicable, heating element amperage draws have been

adjusted for the assumed input voltage. The manufacturer

assumes incoming voltages will be either 208 or 230 Volts. Some

heating elements used in the machines are rated for other voltages,

such as 240 Volts and 480 Volts. Always verify the amperage

draw of the machine in operation when sizing circuit protection.

If the dishmachine is equipped with the optional rinse heater, note

the rinse heater might have its own electrical connection and

require a separate service. Amperage loads for motors and heaters

are indicated on the machine data plate.

The electrical configurations of the DishStar

series of machines

are as follows:

Available Electrical Characteristics:

•

208 V, 60 Hz, Single-phase

•

230 V, 60 Hz, Single-phase

LT/LT-H

•

115 V, 60 Hz, Single-phase

Available Wash Tank Heaters:

•

1.5 kW (LT-H Only)

*The DishStar

LT-H is designed so that the wash motor is never

running when the wash heater is on. Total Load is based on the

higher of the two loads.

VOLTS

208

230

PHASE

FREQ

WASH

MOTOR

AMPS

5.0 A

RINSE

HEATER

AMPS

32.2 A

35.7 A

TOTAL

LOAD

37.2 A

40.7 A

NOTICE

DishStar

VOLTS

115

PHASE

FREQ

WASH

MOTOR

AMPS

5.0 A

TOTAL

LOAD

5.0 A

ELECTRICAL REQUIREMENTS

SPECIFICATIONS

DishStar

LT-H

VOLTS

115

PHASE

FREQ

WASH

MOTOR

AMPS

5.0 A

WASH

HEATER

AMPS

13.1 A

TOTAL

LOAD

13.1 A*

Electrical Characteristics

Содержание DishStar HT





































































Результаты поиска

Содержание DishStar HT

Отзывы:

Похожие инструкции для DishStar HT

Бренды по названию

Популярные бренды

Jackson DishStar HT, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DishStar HT

Отзывы:

Похожие инструкции для DishStar HT

Бренды по названию

Популярные бренды