Jackson DishStar HT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

background image

6

07610-004-37-13-E

WATER SUPPLY

CONNECTION:

WATER HARDNESS

OF 5 GPG

OR LOWER

PRESSURE

REGULATOR

SHOCK ABSORBER

CONNECTING THE

DRAIN LINE

If water hardness tests at 5 GPG or lower, install the water supply line (1/2” ID pipe

size minimum) to the machine’s incoming water connection point using copper pipe

(or order the 1/2” ID flexible hose kit offered by the manufacturer). It is recommended

that a water shut-off valve be installed in the water line between the main supply and
the machine to allow access for service. The water supply line must be capable of a

minimum of 10 PSI “flow” pressure at the recommended temperature indicated on the

data plate.

The manufacturer has an optional water pressure regulator to accommodate areas

where water pressure fluctuates or is higher than the recommended pressure. Take

care not to confuse static pressure with flow pressure: static pressure is line pressure in

a “no flow” condition (all valves and services are closed); flow pressure is the pressure

in the fill line when the valve is opened during the cycle. See the Plumbing Options

page.

It is suggested that a shock absorber (not supplied) be installed on the incoming water
line. This prevents water hammer (hydraulic shock)—induced by the solenoid valve

as it operates—from causing damage to the equipment. See the Plumbing Options

page.

The dishmachine has a pumped (pressure) drain capable of pumping waste water

to a height of 24” above the floor to the kitchen’s drain system. Each dishmachine is

supplied with a drain hose. When installed, it will extend from the rear side of the ma-

chine. There must be an air-gap between the machine drain line and the floor sink or

drain. If a grease trap is required by code, it should have a flow capacity of 12 GPM.

After installing the incoming fill line and the drain line, slowly turn on the water supply

to the machine. Check for any leaks and repair as required. All leaks must be
repaired before operating the machine.

Take care not to confuse

static pressure with

flow pressure!

PLUMBING CHECK

INSTRUCTIONS

INSTALLATION

«
...
11
12
13
14
15
...
»

Содержание DishStar HT





































































Отзывы:

Нет отзывов

Похожие инструкции для DishStar HT

Бренд: Washtech Страницы: 44

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 2

Бренд: Alliance Laundry Systems Страницы: 48

CLW-108i and CLW-128i Installation / Operation / Maintenance M

Бренд: Cole Parmer Страницы: 50

Бренд: Summit Страницы: 1

AQUALTIS AQ93F 69

Бренд: Hotpoint Страницы: 60

Бренд: Daewoo Страницы: 27

Бренд: Admiral Страницы: 6

Бренд: Progress Страницы: 72

Conservator 3955874A

Бренд: Crosley Страницы: 8

Бренд: Maytag Страницы: 27

Бренд: Hallman Страницы: 20

Бренд: Maytag Страницы: 40

Бренд: Maytag Страницы: 12

Бренд: Beko Страницы: 30

Бренд: Beko Страницы: 28

Бренд: Beko Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды