IWILL P55XB2 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 91

IWILL P55XB2 Скачать руководство пользователя страница 78

78

3.6 PnP/ PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or

P

ersonal

C

omputer

I

nterconnect, is a system which allows I/O devices to operate at speeds nearing the

speed the CPU itself uses when communicating with its own special components.
This section covers some very technical items and it is strongly recommended that
only experienced users should make any changes to the default settings.

ROM PCI/ISA BIOS (XXXXXXXX)

PNP/PCI CONFIGURATION

AWARD SOFTWARE, INC.

Resources Controlled By
Reset Configuration Data

Esc : Quit

F1 : Help

(Shift)F2 :Change Color

: Select Item

PU/PD/+/- : Modify

:
:

Enabled
60 ns

F5 : Old Values

F7 : Load Setup Defaults

PCI IRQ Actived By

:
:
:
:

Level
PCI-AUTO

B

A

Primary IDE Int#

IRQ-3
IRQ-4
IRQ-5
IRQ-7
IRQ-9
IRQ-10
IRQ-11
IRQ-12
IRQ-14
IRQ-15
DMA-0
DMA-1
DMA-3
DMA-5
DMA-6
DMA-7

Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :
Assigned to   :

Legacy ISA
Legacy ISA
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP

PCI IRQ Map To

Secondary IDE Int#

The Award Plug and Play BIOS has the capacity to automatically configure all of the
boot and Plug and Play compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system such as
Windows



95.

Choices are

Auto

and

Manual (default).

Resource Controlled

by

«
...
76
77
78
79
80
...
»

Содержание P55XB2




























































































Отзывы:

Нет отзывов