IWILL P55XB2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 91

IWILL P55XB2 Скачать руководство пользователя страница 22

22

Two onboard 10 pin box-header connector provide 2 Serial port. Use the two
cables that goes with this motherboard to convert to the standard 9 and 25 pins
D-Sub connectors.

Two high speed 16550 UART serial port

IRQ selectable from BIOS.

Address changeable form system BIOS

NS16C550 compatible, Programmable Baud Rate Generator

Parallel Port

One onboard 26 pin box-header connector provides the Parallel port. Connect
this parallel port by one 26 pin and convert to 25 pin D-Sub cable that packs
with this motherboard.

IRQ selectable for IRQ5(278h), IRQ7(378h) from system BIOS.

Standard mode

--Compatible with IBM PC/AT Printer port

EPP Mode

--Enhanced Parallel Port compatible(EPP) compatible

ECP Mode

--Microsoft & Hewlett Packard Extended Capabilities Port

(ECP) Compatible

Incorporates ChiProtect Circuit for protection against damage due to
printer power-on

1.2 Specifications

Physical Dimensions:

Length: 280mm / Width: 220mm

Environmental Requirements:

Temperature 0-55 degrees C (operating or storage)

5% to 95% non-condensing relative humidity

«
...
20
21
22
23
24
...
»

Содержание P55XB2




























































































Отзывы:

Нет отзывов