IWILL P55XB2 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 91

IWILL P55XB2 Скачать руководство пользователя страница 71

71

PCI and IDE Configuration

The recovery time is the length of time, measured in CPU clocks, which the system
will delay after the completion of an input/output request. This delay takes place
because the CPU is operating so much faster than the input/output bus that the CPU
must be delayed to allow for the completion of the I/O.

This item allows you to determine the recovery time allowed for 8 bit I/O. Choices
are from NA, 1 to 8 CPU clocks.

1

clock is the default.

This item allows you to determine the recovery time allowed for 16 bit I/O. Choices
are from NA, 1 to 4 CPU clocks.

1

clock is the default.

In order to improve performance, certain space in memory can be reserved for ISA
cards. This memory must be mapped into the memory space below 16 MB.

Enabled

Memory hole supported.

Disabled

Memory hole not supported.

Disabled

is the default.

Peer concurrency means that more than one PCI

device can be active at a time.

Enabled

Multiple PCI devices can be active.

Disabled

Only one PCI device can be active at a time.

Enabled

is the default.

Bit I/O Recovery Time

Bit I/O Recovery Time

Memory Hole At 15M-

16M

Peer

Concurrency

«
...
69
70
71
72
73
...
»

Содержание P55XB2




























































































Отзывы:

Нет отзывов