IWILL P55XB2 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 91

IWILL P55XB2 Скачать руководство пользователя страница 58

58

3.3 BIOS Features Setup

This section allows you to configure your system for basic operation. You have the
opportunity to select the system default speed, boot-up sequence, keyboard operation,
shadowing and security.

ROM PCI/ISA BIOS (XXXXXXXX)

BIOS FEATURES SETUP

AWARD SOFTWARE, INC.

Virus Warning
CPU Internal Cache

Quick Power On Self Test

Boot Up Floppy Seek

Esc : Quit

F1 : Help

(Shift)F2 :Change Color

: Select Item

Swap Floppy Drive

Typematic Rate (Char/Sec)

Typematic Rate Setting

Typematic Delay (Msec)

OS Select For DRAM > 64MB

PCI/VGA palette Snoop

Boot Up System Speed

Boot Up NumLock

PU/PD/+/- : Modify

External Cache

Boot Sequence

Gate A20 option

Security Option

:
:

:

:

:
:

:

:

:
:

:

:

:
:

:

:

Disabled
Enabled

6

Disabled

250

Non-OS2

Disabled

High

On

A, C, SCSI

Fast

Setup

Enabled
Enabled

Disabled
Enabled

Video BIOS Shadow
C800-CBFFF Shadow
CC00-CFFFF Shadow
D000-D3FFF Shadow
D400-D7FFF Shadow
D800-DBFFF Shadow
DC00-DFFFF Shadow

:

:

:
:

:

:

:

Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled

F5 : Old Values

F7 : Load Setup Defaults

When this item is enabled, the Award BIOS will monitor the boot sector and partition
table of the hard disk drive for any attempt at modification. If an attempt is made, the
BIOS will halt the system and the following error message will appear. Afterwards, if
necessary, you will be able to run an anti-virus program to locate and remove the
problem before any damage is done.

! WARNING !

Disk boot sector is to be modified

Type "Y" to accept write or "N" to abort write

Award Software, Inc.

Virus Warning

«
...
56
57
58
59
60
...
»

Содержание P55XB2




























































































Отзывы:

Нет отзывов