ItsImagical DRONI 4 X 1, Руководство пользователя

Страница: 5 / 22

When the left operating lever push up or pull down, the
quadcopter is ascending or descending.
Turning when the left operating lever push left or right, the
quadcopter turns left or right.
When the right operating lever push up/down, the quadcopter
goes forth/back.
When the right operating lever push left or right, the quadcopter
goes to the left or right.
When the quadcopter is hovering and the head of the
quadcopter turns left or right turn the fine tuning to the right or
left until the quadcopter keeps balance.
When the quadcopter is hovering and the quadcopter is deviate
to left or right then turn the side-fly fine tuning to right or left until
the quadcopter keeps balance.
When the quadcopter is hovering and the quadcopter is deviate
to forward or backward, turn the forward/backward fine tuning
up or down until it keeps balance.
Ascend/descend
Turning
Forward/backward
Side Fly
Turning fine tuning
Side-fly fine tuning
Forward backward
fine tuning
Reason
1. Pull to the “OFF” position on
the ON/OFF button.
2. Do not correctly load the
batteries as per the correct
polarity shown.
3. The battery is exhausted.
1. Transmitter is not opened.
2. The ON/OFF button of the
helicopter is on the “OFF “
position.
3. Do not wrench tight the
antenna or the antenna can’t
be completely extended.
4. Too strong wind force.
1. The rotating speed of the
rotator is too slow.
2. The helicopter is not fully
charged.
You pull the power controlling
lever back too quickly.
Problem shooting
1. Pull to the “ON” position on
the ON/OFF button.
2. Check and make sure the
batteries are correctly loaded
as per the polarity shown in
the battery box.
3.Replace with the new
battery
1. Pull to “ON” position on the
ON/OFF button of the
transmitter.
2. Pull to “ON” position on the
ON/OFF button of the
helicopter.
3. Make sure the silver
antenna is wrenched into the
transmitter and extended
completely.
4. Do not fly under the
environment of windy as too
strong wind may cause flying
limitation to the helicopter or it
may hamper your controlling
or flying.
1. Push the power controlling
lever upward.
2. Charge the helicopter till
full.
Slowly pull the power
controlling lever back and let
the helicopter land slowly.
Problem
No power with the
transmitter
Cannot control
The helicopter cannot
ascend
The helicopter lands
too quickly
(EN)
1. INTRODUCTION
This quadcopter is an easy-to-fly, full featured remote control model that can hover, flip,
thrown and fly in all directions with different sensitivities, please read this manual carefully
before operating this product.
2. PARTS NAME
1. Color shell
2. Blade
3. Motor
4. Protection cover (detachable)
5. Color shell
6. Motor
7. Blade
8. Wheel (detachable)
9. Wheel (detachable)
10. Color shell
11. Motor
12. Blade
13. Color shell
14. Blade
15. Motor
A. GAME MODE
B. CRASH MODE
C. GROUND MODE
D. TRICK MODE
1. Trimmer for left/right side-flying of the aileron
2. Power Indicator
3. Trimmer for Ascending/Descending (Forward/Backward)
4. Throttle/aileron (left and right side-flying/high & low speed) control lever.
Press the joystick down to enter the headless mode, press the exit headless mode.
5. Ascending & Descending (Forward / Backward) / Aileron (left or right side flying / 3D
stunt) control lever
6. Power switch
7. Flip
8. Speed Control
Calibration methods: Power frequency after two joystick to the lower left corner while
playing four seconds after letting go quadcopter bottom light starts blinking stops 4 seconds
after a successful calibration.
3. INSTRUCTIONS ON THE QUADCOPTER’S BATTERY CHARGING
Connect USB charging line provided by factory with one end to computer and the other to
the battery to start charging.
The USB’s light is off while charging and turns on while charging completed. The charging
time is about 45 minutes. (Fig. 1)
4. PREPARATION BEFORE TAKING OFF
1. Please operate in spacious indoor or outdoor without rain or snow, and wind power
should be below 4 grade, be away from people, animals and obstacle.
2. Insert the Li-po battery provided by factory into quadcopter. The indication light of the
quadcopter is flashing, then put the quadcopter on leveled place and wait for frequency
adjustment.
3. Pull the acceleration lever to the lowest, turn on the remote control’s switchover, push the
acceleration lever to the highest, then pull it back to the lowest again.
There will be a “di” sound and the quadcopter indication light turns on, then the frequency
adjustment is completed and it is ready for taking off.
5. FLYING CONTROLLED AND FINE TUNING
6. FLYING PARCTICE
1. Accelerating operation: Slowly push the acceleration lever until the quadcopter take off
from the ground and hovers in the air, then pull the acceleration lever back until the
quadcopter slowly descends. Practice this repeatedly until you could control the
acceleration lever smoothly.
2. Vice-blade operation: When the quadcopter hovers in the air, push the right lever slowly
to make the quadcopter fly forward/back ward/to left/to right.
3. Turning operation: When the quadcopter hovers in the air, push the turning rudder slowly
to make the quadcopter turns left or right.
4. 3D Action operation. You can play some thrilling action rolling surface current basic
movements are skilled. Then no amount of rudder upper right corner, click the button on the
remote control, remote controls emit droplets of a sound, this time into the 3D rollover state,
then hit the remote control 3D joystick in any direction to achieve roll, press the remote
controller drops two sounds. Back to conventional flight mode.
TIPS:
1. When matching signal, keep the quadcopter on horizontal position for faster matching
and starting a stable flight.
2. Indoor’s flight: please select spacious place without obstacle, pets and people for flight.
3. Outdoor’s flight: please select a warm sunny and no wind or breeze for flight.
Note:
1. Don’t fly in the extreme weather and the model maybe damaged in extreme heat or cold
weather which will affect flight effect.
2. Don’t fly in the strong wind weather which will cause limitations to the flight or hinder your
flight control. In the case of strong wind, your aircraft will vanish or damage.
Calibration:
If the trim buttons do not correct the problem, you will have to recalibrate your drone. Place
the drone on a flat surface. Push the throttle and direction stick to the lower left. The light on
the remote will be flash. Hold this position for 3 seconds and release. The light will stop
flashing and the drone has recalibrated.
7. COMMON PROBLEM AND SOLUTION INSTRUCTIONS
8. ACCESSORIES
1. Clockwise blades x 2
2. Counter-clockwise blades x 2
3. Reversal blades x 2
4. Reversal motor x 2
5. Upper shell x 1
6. Lower shell x 1
7. Battery x 1
8. Receiver board x 1
4