manualshive.com logo in svg

ITRON MC3Lite, Руководство по установке, Страница: 40 / 44

Поделиться
Скачать
ITRON MC3Lite Скачать руководство пользователя страница 40

Note:

The USB cable is connected to the vehicle dock at the factory and is secured with

a cable tie. Do not remove this cable tie or unplug the USB cable from the vehicle dock.

The cable tie helps ensure a secure connection and should never be disconnected.

2. Plug the round end of the USB cable connector into the USB-labeled receptacle on the MC3

or MC3Lite radio.

Connecting the GPS Antenna Cable

Attach the GPS antenna cable from the roof antenna to the connector on the MC3Lite or MC3

radio labeled GPS.

Note:

When powered on, the LED indicator is lit to indicate that the GPS antenna is

functioning properly. If the LED indicator is not lit, disconnect and reattach the cable to the

GPS antenna connector. If the LED indicator is lit, continue installing your Mobile Collection

system. If the LED indicator remains unlit, contact Itron support.

Removing the Mobile Collection System

At some point, you may need to remove the Mobile Collection system from the vehicle. This

consists of two tasks.

07 May 2020

815-0207-00 REV 000

Itron, Inc. Page 40 of 44

Vehicle Preparation and Hardware Installation Guide

3  Installing Mobile Collection Components

Содержание MC3Lite













































Отзывы:

Нет отзывов