manualshive.com logo in svg

ITRON MC3Lite, Руководство по установке, Страница: 13 / 44

Поделиться
Скачать
ITRON MC3Lite Скачать руководство пользователя страница 13

ID

Component

1

Mounting stud

2

Locating tab

3

Washer

4

Hex nut

Installing the RF Antenna Cable and Mounting Base

1. At your selected location, cut a 0.75 (3/4) inch hole in the mounting surface for the mounting

stud to pass through.

2. Cut a 0.218 (7/32) inch hole that is 0.85 inches from the center of the first hole for the locating

tab.

3. Clean the mounting surface and bottom of the antenna.

4. Feed the cables through the large hole and route to desired locations inside the vehicle:

Mobile Collector mounting location and, if applicable, the GPS receiver location.

5. Apply a bead of silicone sealant around both holes.

6. Position the antenna on the mounting surface, inserting the mounting stud through the large

hole and the locating tab in the small hole.

7. From under the mounting surface (inside the vehicle), slide the washer on the mounting stud

and screw on the hex nut.

8. Tighten the hex nut until the gasket on the base of the antenna compresses to 50% of its

original thickness.

07 May 2020

815-0207-00 REV 000

Itron, Inc. Page 13 of 44

Vehicle Preparation and Hardware Installation Guide

2  Vehicle Preparation

Содержание MC3Lite













































Отзывы:

Нет отзывов