Isokern 82L120 Скачать руководство пользователя страница 40

40

Earthcore Industries

Isokern Maximus Linear Series Gas Fireplace 

01/2020

Isoflames Linear Burner - Safety Instructions

16. 

To prevent performance problems, do not use propane fuel tank of less than 100 lbs. capacity.

17. 

This decorative gas appliance reaches high temperature. Keep children and adults away from hot surfaces to avoid burns or 

clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

18.

 Turn the appliance off and allow to cool before servicing. Always shut off any electricity and gas to the appliance while 

working on it. Only a qualified service person should install, service or repair this appliance. Have your appliance inspected 

annually by a qualified service person.

19. 

It is imperative that the unit’s control areas, burners and circulation air passages be kept clean.

20.

 Keep all combustible material, gasoline and other flammable liquids at a safe distance from the fireplace. Do not use the 

appliance where these items are used or stored. Decorations, clothing and other such combustible items should not be placed 

on the appliance.

21.

 Do not cook food or burn paper or other object(s).

22. 

Do not use any solid fuels - wood, coal, paper, cardboard, etc. - Use only the gas type listed on the fireplace’s gas log label.

23. 

Do not in any way obstruct the flow of combustion and ventilation air. Provide adequate clearances around air openings into

the combustion chamber as well as adequate accessibility clearances for servicing and proper operation.

24.

 This American Gas Association fact sheet provides an overview of the requirements for the electrical bonding of fuel gas 

piping systems to the electrical grounding system based on ANSI Z223.1/NFPA 54, National Fuel Gas Code - 2015 (NFGC). The 

bonding requirements in previous code editions, in local jurisdictions or in specific situations, may differ.

25. 

Never install an ISOFLAMES Linear Burner component or accessory that has visible or suspected physical damage as a 

result of handling or transportation. These items should be inspected by a qualified representative to ensure safe condition. 

When in doubt, consult your local supplier.

26. 

Do not alter or modify the ISOFLAMES Linear Burner or burner components under any circumstances. Modification or 

alteration of any sort may void manufacturer’s warranty, listings and approvals.

27.

 The ISOFLAMES Linear Burner system is not intended to heat an entire home or to be used as a heat source.

28. 

Children and adults should be alerted to the hazards of high surface temperature and should stay away from this appliance 

to avoid burns or clothing ignition.

29. 

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children 

and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at-risk individuals in

the house. To restrict access to the fireplace, install a adjustable safety gate to keep toddlers, young children and other at-risk

individuals out of the room and away from hot surfaces.

30. 

Clothing or flammable material should not be placed on or near the appliance.

31.

 Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

32.

 Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to operating the appliance.

33. 

Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at 

least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, 

bedding material, etcetera. It is imperative that control compartments, burners, and circulating air passageways of the 

appliance be kept clean. 

Содержание 82L120



























































Отзывы: