iSMA iSMA-B-LP-1 Скачать руководство пользователя страница 62

Страница: 62 / 122

iSMA-B-LP Room Panel/Modbus

version 1.3

www.gc5.pl

Page 61 / 121

List of all Modbus Registers

The table below shows all registers available for the Room Panel.

Modbus
Address

Dec

Address

Hex

Address

Access

Description

40001

0x00

VERSION_TYPE

Read & Write

First byte means version and another one type of a

device. Allows to enable 1 of 4 device actions.

30004

0x03

RECEIVED__FRAMES

COUNTER (32

–

bits)

Read Only

Default state is 0. Reset at the unit start and change

of transmission parameters.

30006

0x05

ERROR_FRAMES

COUNTER (32

–

bits)

Read Only

Default state is 0. Reset at the unit start and change

of transmission parameters.

30008

0x07

TRANSMITTED_FRAME

COUNTER _(32

–

bits)

Read Only

Default state is 0. Reset at the unit start and change

of transmission parameters.

30012

0x0C

LIVE_TIME

(32

–

bits)

Read Only

Up device time in sec

40015

0x0E

BACNET_DEVICE_ID

(32

–

bits)

Read & Write

Memory

Default 0xFFFFFFFF

40017

0x10

BAUD_RATE

Read & Write

Memory

Transmission speed is defined by the user,

calculation using the formula:

The default value is 11520 (115200 bps)

40018

0x11

STOP_BITS

Read & Write

Memory

Supported values are 1 and 2

The default value 1

40020

0x13

PARITY_BIT

Read & Write

Memory

The default value is 0 (no parity)

Allowed values:

Value

Description

0 (default)

none

Odd

Even

40021

0x14

REPLAY_DELAY

Read & Write

Memory

Delay in ms before sending response

The default value is 0.

40023

0x16

ADDRESS

Read & Write

Memory

Modbus address of the device.

The default value is 1.

40024

0x17

PROTOCOL

Read & Write

Memory

–

Modbus RTU (default)

–

Modbus ASCII

–

BACnet MS/TP

40028

0x1B

PANEL_PASSWORD

Read & Write

Memory

Password for Menu Edit Mode. Default is 1000.

30029

0x1C

SENSORS

Read Only

BIT0

–

humidity sensor

BIT1

–

CO2 sensor

BIT2

–

NTC sensor

30201

200

0xC8

BACKGROUND_ILLUMINATION

LCD_CURRENT_VALUE

Read Only

Actual display illumination value

30202

201

0xC9

BACKGROUND_ILLUMINATION

Read Only

Actual Key Pad illumination value

Содержание iSMA-B-LP-1



























































































































Результаты поиска

Содержание iSMA-B-LP-1

Отзывы:

Похожие инструкции для iSMA-B-LP-1

Бренды по названию

Популярные бренды

iSMA iSMA-B-LP-1, Руководство пользователя

Результаты поиска

Содержание iSMA-B-LP-1

Отзывы:

Похожие инструкции для iSMA-B-LP-1

Бренды по названию

Популярные бренды