IS5COM IES26G Series Скачать руководство пользователя страница 56

Страница: 56 / 79

iES26G Series User’s Manual

iS5 Communications Inc.

Port Counters interface

The following table describes the labels for the Port Counters screen.

Label

Description

Select Port

View Port Counters for selected Port.

RxBcastPkts

Number of good broadcast packets received.

RxOctets

Number of total of packets received, in bytes. (including those in bad
packets)

RxMcastPkts

Number of good multicast packets received. (excluding broadcast
packets)

RxFCSErr

Number of bad FCS packets received with the proper and integral
octets.

RxOverSizePkt

Number of packets received with a frame size between 1522
and 9022.

RxAlignErr

Number of bad FCS packets received with the proper and non-
integral octets.

RxJabber

Number of packets received over the frame size 9022.

RxFragment

Number of packets received less than 64 in frame size,
including bad FCS packets.

RxUnderSizePkt

Number of packets received less than 64 in frame size.

RxPkt64

Number of packets received the 64 of frame size, including bad
packets.

RxPkt65to127

Number of packets received from 65 to 127 of frame size,
including bad packets.

RxPkt128to255

Number of packets received from 128 to 255 of frame size,
including bad packets.

RxPkt256to511

Number of packets received from 256 to 511 of frame size,
including bad packets.

RxPkt512to1023

Number of packets received from 512 to 1023 of frame size,
including bad packets.

RxPkt1024to1522

Number of packets received from 1024 to 1522 of frame size,
including bad packets.

TxUcastPkt

Number of unicast packets transmitted.

TxBcastPkt

Number of broadcast packets transmitted.

TxOctet

Number of total packets transmitted, the unit is byte.
(including those in good packets)

TxSingleCollisn

Number of successfully transmitted packets which transmission
is inhibited by exactly one collision.

TxMultiCollisn

Number of successfully transmitted packets which transmission
is inhibited by more than one collision.

TxCollisn

Number of collision on this Ethernet segment.

TxDefferTrans

Number of packets for which the first transmission attempt is
delayed because medium is busy.

Содержание IES26G Series
















































































Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды

IS5COM IES26G Series, Руководство пользователя

Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды