IS5COM IES26G Series Скачать руководство пользователя страница 22

Страница: 22 / 79

iES26G Series User’s Manual

iS5 Communications Inc.

Backup Configuration interface

The following table describes the labels for the Backup & Restore Configuration screen.

Label

Description

TFTP Server IP Address

Enter the TFTP server IP.

Restore File Name

Enter the file name to be loaded onto the switch.

Restore

Click “

restore

” to restore the configurations.

From a Local PC

The user can also restore the configuration from a file on a local PC. In
this case there is no need for the TFTP server.

Backup File Name

Enter the file name to create the backup file.

Restore

Click “

restore

” to restore the configurations.

Backup

Click “

backup

” to backup the configurations.

To Local PC

The user can also backup configuration files to a local PC. A TFTP
server is not required in this case.

4.1.3.7

Upgrade Firmware

Upgrade Firmware allows the user to update the firmware of the switch via the TPTP or

from a local PC. Before updating via the TFTP server, make sure you have the TFTP server

ready and the firmware image is on the TFTP server.

Upgrade Firmware interface

Содержание IES26G Series
















































































Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды

IS5COM IES26G Series, Руководство пользователя

Результаты поиска

Содержание IES26G Series

Отзывы:

Похожие инструкции для IES26G Series

Бренды по названию

Популярные бренды